προβλημα με wi-fi
προβλημα με wi-fi
εχω παρει μια ασυρματη καρτα που κουμπώνει σε pci
αφου την εβαλα και πα στα δικτυα μου βγαζει την παρακάτω εικόνα
https://www.flickr.com/photos/99709873@ ... otostream/
το πακέτο firmware-Ralink το έχω εγκαταστήσει
αφου την εβαλα και πα στα δικτυα μου βγαζει την παρακάτω εικόνα
https://www.flickr.com/photos/99709873@ ... otostream/
το πακέτο firmware-Ralink το έχω εγκαταστήσει
Intel Core i5-6300U CPU @ 2.40GHz ‖ RAM 7860 MiB ‖ HP 8079 - HP HP EliteBook 840 G3
Intel Skylake GT2 [HD Graphics 520] [8086:1916] {i915}
wlp2s0: Intel Wireless 8260 [8086:24f3] (rev 3a) ⋮ enp0s31f6: Intel Ethernet Connection I219-LM [8086:156f] (rev 21)
Intel Skylake GT2 [HD Graphics 520] [8086:1916] {i915}
wlp2s0: Intel Wireless 8260 [8086:24f3] (rev 3a) ⋮ enp0s31f6: Intel Ethernet Connection I219-LM [8086:156f] (rev 21)
- dglent
- Δημοσιεύσεις: 1069
- Εγγραφή: Τετ Ιουν 01, 2011 05:42 am
- Τοποθεσία: Γαλλία
- Has thanked: 6 φορές
Re: προβλημα με wi-fi
Γράψε και το μοντέλο της κάρτας και ποιο άρθρωμα χρησιμοποιεί μήπως βρούμε πληροφορίες και σε ξένα φόρουμ
και την έξοδο των εντολών:
lpcidrake
dmesg
και την έξοδο των εντολών:
lpcidrake
dmesg
Re: προβλημα με wi-fi
αυτο ειναι το μοντελο
http://www.netis-systems.com/en/product ... 1DA-PEvBDU
δίνω
http://www.netis-systems.com/en/product ... 1DA-PEvBDU
δίνω
Κώδικας: Επιλογή όλων
dmesg
Κώδικας: Επιλογή όλων
[ 0.136203] pci 0000:00:1f.2: reg 0x14: [io 0x0000-0x0003]
[ 0.136210] pci 0000:00:1f.2: reg 0x18: [io 0x0000-0x0007]
[ 0.136216] pci 0000:00:1f.2: reg 0x1c: [io 0x0000-0x0003]
[ 0.136223] pci 0000:00:1f.2: reg 0x20: [io 0xf000-0xf00f]
[ 0.136252] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.136308] pci 0000:00:1f.3: [8086:27da] type 00 class 0x0c0500
[ 0.136352] pci 0000:00:1f.3: reg 0x20: [io 0x0500-0x051f]
[ 0.136458] pci 0000:01:00.0: [10de:0640] type 00 class 0x030000
[ 0.136467] pci 0000:01:00.0: reg 0x10: [mem 0xe2000000-0xe2ffffff]
[ 0.136476] pci 0000:01:00.0: reg 0x14: [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.136485] pci 0000:01:00.0: reg 0x1c: [mem 0xe0000000-0xe1ffffff 64bit]
[ 0.136492] pci 0000:01:00.0: reg 0x24: [io 0xc000-0xc07f]
[ 0.136498] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0007ffff pref]
[ 0.136563] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.136566] pci 0000:00:01.0: bridge window [io 0xc000-0xcfff]
[ 0.136568] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe3ffffff]
[ 0.136572] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.136614] pci 0000:00:1c.0: PCI bridge to [bus 02]
[ 0.136617] pci 0000:00:1c.0: bridge window [io 0xb000-0xbfff]
[ 0.136679] pci 0000:03:00.0: [10ec:8136] type 00 class 0x020000
[ 0.136694] pci 0000:03:00.0: reg 0x10: [io 0xd000-0xd0ff]
[ 0.136719] pci 0000:03:00.0: reg 0x18: [mem 0xe5010000-0xe5010fff 64bit pref]
[ 0.136735] pci 0000:03:00.0: reg 0x20: [mem 0xe5000000-0xe500ffff 64bit pref]
[ 0.136746] pci 0000:03:00.0: reg 0x30: [mem 0x00000000-0x0001ffff pref]
[ 0.136804] pci 0000:03:00.0: supports D1 D2
[ 0.136805] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.138021] pci 0000:00:1c.1: PCI bridge to [bus 03]
[ 0.138027] pci 0000:00:1c.1: bridge window [io 0xd000-0xdfff]
[ 0.138032] pci 0000:00:1c.1: bridge window [mem 0xe4000000-0xe4ffffff]
[ 0.138039] pci 0000:00:1c.1: bridge window [mem 0xe5000000-0xe50fffff 64bit pref]
[ 0.138091] pci 0000:04:01.0: [1814:5362] type 00 class 0x028000
[ 0.138110] pci 0000:04:01.0: reg 0x10: [mem 0xe5100000-0xe510ffff]
[ 0.138246] pci 0000:00:1e.0: PCI bridge to [bus 04] (subtractive decode)
[ 0.138251] pci 0000:00:1e.0: bridge window [mem 0xe5100000-0xe51fffff]
[ 0.138256] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 0.138257] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 0.138259] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.138261] pci 0000:00:1e.0: bridge window [mem 0x000c0000-0x000dffff] (subtractive decode)
[ 0.138263] pci 0000:00:1e.0: bridge window [mem 0xbff00000-0xfebfffff] (subtractive decode)
[ 0.138651] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[ 0.138698] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[ 0.138744] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[ 0.138789] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 0.138834] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.138880] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.138925] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.138971] ACPI: PCI Interrupt Link [LNK1] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
[ 0.139050] ACPI: Enabled 1 GPEs in block 00 to 1F
[ 0.139056] ACPI: \_SB_.PCI0: notify handler is installed
[ 0.139077] Found 1 acpi root devices
[ 0.139133] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.139133] vgaarb: loaded
[ 0.139133] vgaarb: bridge control possible 0000:01:00.0
[ 0.139133] SCSI subsystem initialized
[ 0.139133] libata version 3.00 loaded.
[ 0.139133] PCI: Using ACPI for IRQ routing
[ 0.144262] PCI: pci_cache_line_size set to 64 bytes
[ 0.144297] e820: reserve RAM buffer [mem 0x0009f800-0x0009ffff]
[ 0.144299] e820: reserve RAM buffer [mem 0xbfee0000-0xbfffffff]
[ 0.144379] NetLabel: Initializing
[ 0.144380] NetLabel: domain hash size = 128
[ 0.144381] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.144390] NetLabel: unlabeled traffic allowed by default
[ 0.144415] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.144418] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.144421] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.146013] Switched to clocksource hpet
[ 0.151323] pnp: PnP ACPI init
[ 0.151339] ACPI: bus type PNP registered
[ 0.151508] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.151517] pnp 00:01: [dma 4]
[ 0.151532] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.151604] pnp 00:02: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.151636] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.151658] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.151680] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.151894] pnp 00:06: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.152063] pnp 00:07: Plug and Play ACPI device, IDs PNP0400 (active)
[ 0.152145] pnp 00:08: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.152195] system 00:09: [io 0x0400-0x04cf] could not be reserved
[ 0.152198] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.152355] system 00:0a: [mem 0xc0000000-0xcfffffff] has been reserved
[ 0.152358] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.152498] system 00:0b: [mem 0x000ce000-0x000cffff] has been reserved
[ 0.152524] system 00:0b: [mem 0x000e0000-0x000effff] has been reserved
[ 0.152526] system 00:0b: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.152556] pnp 00:0c: Plug and Play ACPI device, IDs INT0800 (active)
[ 0.152560] pnp: PnP ACPI: found 13 devices
[ 0.152561] ACPI: bus type PNP unregistered
[ 0.158537] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000
[ 0.158540] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 02] add_size 200000
[ 0.158553] pci 0000:00:1f.0: BAR 13: [io 0x0400-0x047f] has bogus alignment
[ 0.158556] pci 0000:00:1c.0: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
[ 0.158558] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 0.158563] pci 0000:00:1c.0: BAR 14: assigned [mem 0xe5300000-0xe54fffff]
[ 0.158565] pci 0000:00:1c.0: BAR 15: assigned [mem 0xe5500000-0xe56fffff 64bit pref]
[ 0.158568] pci 0000:01:00.0: BAR 6: assigned [mem 0xe3000000-0xe307ffff pref]
[ 0.158571] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.158573] pci 0000:00:01.0: bridge window [io 0xc000-0xcfff]
[ 0.158576] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe3ffffff]
[ 0.158579] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.158582] pci 0000:00:1c.0: PCI bridge to [bus 02]
[ 0.158584] pci 0000:00:1c.0: bridge window [io 0xb000-0xbfff]
[ 0.158588] pci 0000:00:1c.0: bridge window [mem 0xe5300000-0xe54fffff]
[ 0.158591] pci 0000:00:1c.0: bridge window [mem 0xe5500000-0xe56fffff 64bit pref]
[ 0.158597] pci 0000:03:00.0: BAR 6: assigned [mem 0xe5020000-0xe503ffff pref]
[ 0.158599] pci 0000:00:1c.1: PCI bridge to [bus 03]
[ 0.158601] pci 0000:00:1c.1: bridge window [io 0xd000-0xdfff]
[ 0.158605] pci 0000:00:1c.1: bridge window [mem 0xe4000000-0xe4ffffff]
[ 0.158608] pci 0000:00:1c.1: bridge window [mem 0xe5000000-0xe50fffff 64bit pref]
[ 0.158613] pci 0000:00:1e.0: PCI bridge to [bus 04]
[ 0.158617] pci 0000:00:1e.0: bridge window [mem 0xe5100000-0xe51fffff]
[ 0.158623] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.158625] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.158627] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.158629] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff]
[ 0.158630] pci_bus 0000:00: resource 8 [mem 0xbff00000-0xfebfffff]
[ 0.158632] pci_bus 0000:01: resource 0 [io 0xc000-0xcfff]
[ 0.158634] pci_bus 0000:01: resource 1 [mem 0xe0000000-0xe3ffffff]
[ 0.158636] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.158638] pci_bus 0000:02: resource 0 [io 0xb000-0xbfff]
[ 0.158639] pci_bus 0000:02: resource 1 [mem 0xe5300000-0xe54fffff]
[ 0.158641] pci_bus 0000:02: resource 2 [mem 0xe5500000-0xe56fffff 64bit pref]
[ 0.158643] pci_bus 0000:03: resource 0 [io 0xd000-0xdfff]
[ 0.158645] pci_bus 0000:03: resource 1 [mem 0xe4000000-0xe4ffffff]
[ 0.158646] pci_bus 0000:03: resource 2 [mem 0xe5000000-0xe50fffff 64bit pref]
[ 0.158648] pci_bus 0000:04: resource 1 [mem 0xe5100000-0xe51fffff]
[ 0.158650] pci_bus 0000:04: resource 4 [io 0x0000-0x0cf7]
[ 0.158652] pci_bus 0000:04: resource 5 [io 0x0d00-0xffff]
[ 0.158654] pci_bus 0000:04: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.158655] pci_bus 0000:04: resource 7 [mem 0x000c0000-0x000dffff]
[ 0.158657] pci_bus 0000:04: resource 8 [mem 0xbff00000-0xfebfffff]
[ 0.158688] NET: Registered protocol family 2
[ 0.158852] TCP established hash table entries: 32768 (order: 7, 524288 bytes)
[ 0.159085] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[ 0.159279] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.159320] TCP: reno registered
[ 0.159330] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.159358] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.159433] NET: Registered protocol family 1
[ 0.159937] pci 0000:01:00.0: Boot video device
[ 0.159944] PCI: CLS 32 bytes, default 64
[ 0.159984] Trying to unpack rootfs image as initramfs...
[ 0.246734] Freeing initrd memory: 7956K (ffff880037066000 - ffff88003782b000)
[ 0.246742] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.246744] software IO TLB [mem 0xbbee0000-0xbfee0000] (64MB) mapped at [ffff8800bbee0000-ffff8800bfedffff]
[ 0.247165] audit: initializing netlink socket (disabled)
[ 0.247179] type=2000 audit(1397800527.246:1): initialized
[ 0.267608] bounce pool size: 64 pages
[ 0.267619] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.268801] zbud: loaded
[ 0.268925] VFS: Disk quotas dquot_6.5.2
[ 0.268960] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.269374] bio: create slab <bio-1> at 1
[ 0.269502] Btrfs loaded
[ 0.269507] msgmni has been set to 7900
[ 0.269731] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.269755] io scheduler noop registered
[ 0.269757] io scheduler deadline registered
[ 0.269780] io scheduler cfq registered (default)
[ 0.269929] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[ 0.270020] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
[ 0.270118] pcieport 0000:00:1c.1: irq 42 for MSI/MSI-X
[ 0.270177] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.270189] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.270232] intel_idle: does not run on family 6 model 23
[ 0.270258] GHES: HEST is not enabled!
[ 0.270296] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.290780] 00:06: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[ 0.291053] Linux agpgart interface v0.103
[ 0.292116] brd: module loaded
[ 0.292223] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 0.292225] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 0.292344] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.292409] mousedev: PS/2 mouse device common for all mice
[ 0.292483] rtc_cmos 00:03: RTC can wake from S4
[ 0.292578] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 0.292600] rtc_cmos 00:03: alarms up to one month, 242 bytes nvram, hpet irqs
[ 0.292609] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.292693] TCP: cubic registered
[ 0.292703] Key type dns_resolver registered
[ 0.292704] mpls_gso: MPLS GSO support
[ 0.292847] registered taskstats version 1
[ 0.293296] Magic number: 10:757:921
[ 0.293365] rtc_cmos 00:03: setting system clock to 2014-04-18 05:55:28 UTC (1397800528)
[ 0.293367] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.293368] EDD information not available.
[ 0.293394] PM: Checking hibernation image partition UUID=db01d9fc-7995-4da3-b5e7-46c6d7448c59
[ 0.311640] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 0.311659] PM: Hibernation image not present or could not be loaded.
[ 0.312616] Freeing unused kernel memory: 1232K (ffffffff81cdb000 - ffffffff81e0f000)
[ 0.312617] Write protecting the kernel read-only data: 12288k
[ 0.316655] Freeing unused kernel memory: 1900K (ffff880001625000 - ffff880001800000)
[ 0.319017] Freeing unused kernel memory: 1072K (ffff880001af4000 - ffff880001c00000)
[ 0.355120] dracut: dracut-034
[ 0.364765] ata_piix 0000:00:1f.2: version 2.13
[ 0.364856] ata_piix 0000:00:1f.2: MAP [
[ 0.364857] P0 P2 IDE IDE ]
[ 0.364888] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 0.365365] scsi0 : ata_piix
[ 0.365434] scsi1 : ata_piix
[ 0.365458] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[ 0.365460] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[ 0.519405] ata2.00: ATAPI: Optiarc DVD RW AD-7200A, 1.09, max UDMA/66
[ 0.520184] ata1.00: HPA detected: current 976771055, native 976773168
[ 0.520189] ata1.00: ATA-8: WDC WD5000AAKX-001CA0, 15.01H15, max UDMA/133
[ 0.520192] ata1.00: 976771055 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 0.525198] ata2.00: configured for UDMA/66
[ 0.526265] ata1.00: configured for UDMA/133
[ 0.526355] scsi 0:0:0:0: Direct-Access ATA WDC WD5000AAKX-0 15.0 PQ: 0 ANSI: 5
[ 0.526435] sd 0:0:0:0: [sda] 976771055 512-byte logical blocks: (500 GB/465 GiB)
[ 0.526486] sd 0:0:0:0: [sda] Write Protect is off
[ 0.526489] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 0.526547] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 0.528086] scsi 1:0:0:0: CD-ROM Optiarc DVD RW AD-7200A 1.09 PQ: 0 ANSI: 5
[ 0.560536] sda: sda1 sda2 sda3
[ 0.560605] sda: p3 size 8192000 extends beyond EOD, enabling native capacity
[ 0.560617] ata1: soft resetting link
[ 0.717129] ata1.00: n_sectors mismatch 976771055 != 976773168
[ 0.717132] ata1.00: new n_sectors matches native, probably late HPA unlock, n_sectors updated
[ 0.723392] ata1.00: configured for UDMA/133
[ 0.723397] ata1: EH complete
[ 0.723434] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 0.723693] sda: detected capacity change from 500106780160 to 500107862016
[ 0.777195] sda: sda1 sda2 sda3
[ 0.777435] sd 0:0:0:0: [sda] Attached SCSI disk
[ 0.789181] Uniform Multi-Platform E-IDE driver
[ 0.851258] systemd-udevd[191]: starting version 208
[ 0.891054] [drm] Initialized drm 1.1.0 20060810
[ 0.897977] wmi: Mapper loaded
[ 0.899669] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 0.899674] ACPI: Power Button [PWRB]
[ 0.899725] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 0.899728] ACPI: Power Button [PWRF]
[ 0.931854] [drm] hdmi device not found 1 0 1
[ 0.931939] nouveau [ DEVICE][0000:01:00.0] BOOT0 : 0x096000c1
[ 0.931941] nouveau [ DEVICE][0000:01:00.0] Chipset: G96 (NV96)
[ 0.931943] nouveau [ DEVICE][0000:01:00.0] Family : NV50
[ 0.932888] nouveau [ VBIOS][0000:01:00.0] checking PRAMIN for image...
[ 0.984297] nouveau [ VBIOS][0000:01:00.0] ... appears to be valid
[ 0.984298] nouveau [ VBIOS][0000:01:00.0] using image from PRAMIN
[ 0.984396] nouveau [ VBIOS][0000:01:00.0] BIT signature found
[ 0.984398] nouveau [ VBIOS][0000:01:00.0] version 62.94.4b.00.00
[ 1.004580] nouveau [ PFB][0000:01:00.0] RAM type: DDR2
[ 1.004582] nouveau [ PFB][0000:01:00.0] RAM size: 1024 MiB
[ 1.004584] nouveau [ PFB][0000:01:00.0] ZCOMP: 2048 tags
[ 1.027062] nouveau [ PTHERM][0000:01:00.0] FAN control: PWM
[ 1.027070] nouveau [ PTHERM][0000:01:00.0] fan management: disabled
[ 1.027073] nouveau [ PTHERM][0000:01:00.0] internal sensor: yes
[ 1.027188] [TTM] Zone kernel: Available graphics memory: 2024612 kiB
[ 1.027190] [TTM] Initializing pool allocator
[ 1.027194] [TTM] Initializing DMA pool allocator
[ 1.027201] nouveau [ DRM] VRAM: 1024 MiB
[ 1.027202] nouveau [ DRM] GART: 1048576 MiB
[ 1.027205] nouveau [ DRM] TMDS table version 2.0
[ 1.027206] nouveau [ DRM] DCB version 4.0
[ 1.027208] nouveau [ DRM] DCB outp 00: 02000300 00000028
[ 1.027210] nouveau [ DRM] DCB outp 01: 01000302 00020030
[ 1.027212] nouveau [ DRM] DCB outp 02: 04011310 00000028
[ 1.027213] nouveau [ DRM] DCB outp 03: 02021342 00020030
[ 1.027215] nouveau [ DRM] DCB outp 04: 010223f1 00c0c080
[ 1.027216] nouveau [ DRM] DCB conn 00: 00001030
[ 1.027218] nouveau [ DRM] DCB conn 01: 00002130
[ 1.027220] nouveau [ DRM] DCB conn 02: 00000200
[ 1.035841] nouveau W[ DRM] failed to create encoder 0/1/0: -19
[ 1.035843] nouveau W[ DRM] VGA-1 has no encoders, removing
[ 1.035862] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 1.035863] [drm] No driver support for vblank timestamp query.
[ 1.035955] nouveau [ DRM] 1 available performance level(s)
[ 1.035958] nouveau [ DRM] 3: core 550MHz shader 1375MHz memory 333MHz fanspeed 100%
[ 1.035960] nouveau [ DRM] c: core 400MHz shader 800MHz memory 300MHz fanspeed 40%
[ 1.247018] tsc: Refined TSC clocksource calibration: 2933.297 MHz
[ 1.295149] nouveau [ DRM] MM: using CRYPT for buffer copies
[ 1.338998] nouveau [ DRM] allocated 1440x900 fb: 0x70000, bo ffff88003729ac00
[ 1.339047] fbcon: nouveaufb (fb0) is primary device
[ 1.417322] Console: switching to colour frame buffer device 180x56
[ 1.418927] nouveau 0000:01:00.0: fb0: nouveaufb frame buffer device
[ 1.418928] nouveau 0000:01:00.0: registered panic notifier
[ 1.418932] [drm] Initialized nouveau 1.1.1 20120801 for 0000:01:00.0 on minor 0
[ 1.420992] dracut: Starting plymouth daemon
[ 2.247079] Switched to clocksource tsc
[ 2.624893] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 2.624897] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 2.624991] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 2.643104] ACPI: bus type USB registered
[ 2.643131] usbcore: registered new interface driver usbfs
[ 2.643139] usbcore: registered new interface driver hub
[ 2.646043] usbcore: registered new device driver usb
[ 2.649277] uhci_hcd: USB Universal Host Controller Interface driver
[ 2.649400] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 2.649403] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.649409] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 2.649447] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000e000
[ 2.651259] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.651262] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.651264] usb usb1: Product: UHCI Host Controller
[ 2.651266] usb usb1: Manufacturer: Linux 3.12.13-desktop-2.mga4 uhci_hcd
[ 2.651268] usb usb1: SerialNumber: 0000:00:1d.0
[ 2.651370] hub 1-0:1.0: USB hub found
[ 2.651377] hub 1-0:1.0: 2 ports detected
[ 2.651540] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 2.651543] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 2.651548] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[ 2.651583] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e100
[ 2.651623] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.651625] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.651627] usb usb2: Product: UHCI Host Controller
[ 2.651628] usb usb2: Manufacturer: Linux 3.12.13-desktop-2.mga4 uhci_hcd
[ 2.651630] usb usb2: SerialNumber: 0000:00:1d.1
[ 2.651698] hub 2-0:1.0: USB hub found
[ 2.651704] hub 2-0:1.0: 2 ports detected
[ 2.651820] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 2.651823] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 2.651827] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[ 2.651853] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e200
[ 2.652030] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.652033] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.652035] usb usb3: Product: UHCI Host Controller
[ 2.652036] usb usb3: Manufacturer: Linux 3.12.13-desktop-2.mga4 uhci_hcd
[ 2.652038] usb usb3: SerialNumber: 0000:00:1d.2
[ 2.652115] hub 3-0:1.0: USB hub found
[ 2.652122] hub 3-0:1.0: 2 ports detected
[ 2.654200] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 2.654204] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 2.654210] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[ 2.654234] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000e300
[ 2.654277] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.654279] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.654281] usb usb4: Product: UHCI Host Controller
[ 2.654282] usb usb4: Manufacturer: Linux 3.12.13-desktop-2.mga4 uhci_hcd
[ 2.654284] usb usb4: SerialNumber: 0000:00:1d.3
[ 2.654363] hub 4-0:1.0: USB hub found
[ 2.654370] hub 4-0:1.0: 2 ports detected
[ 2.664872] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.664875] Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
[ 2.665344] ehci-pci: EHCI PCI platform driver
[ 2.665465] ehci-pci 0000:00:1d.7: setting latency timer to 64
[ 2.666597] ehci-pci 0000:00:1d.7: EHCI Host Controller
[ 2.666605] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 5
[ 2.670530] ehci-pci 0000:00:1d.7: cache line size of 32 is not supported
[ 2.670739] ehci-pci 0000:00:1d.7: irq 23, io mem 0xe5204000
[ 2.676013] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 2.676077] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.676079] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.676081] usb usb5: Product: EHCI Host Controller
[ 2.676082] usb usb5: Manufacturer: Linux 3.12.13-desktop-2.mga4 ehci_hcd
[ 2.676084] usb usb5: SerialNumber: 0000:00:1d.7
[ 2.676233] hub 5-0:1.0: USB hub found
[ 2.676257] hub 5-0:1.0: 8 ports detected
[ 2.697092] hub 1-0:1.0: USB hub found
[ 2.697107] hub 1-0:1.0: 2 ports detected
[ 2.718127] hub 2-0:1.0: USB hub found
[ 2.718138] hub 2-0:1.0: 2 ports detected
[ 2.739075] hub 3-0:1.0: USB hub found
[ 2.739095] hub 3-0:1.0: 2 ports detected
[ 2.760059] hub 4-0:1.0: USB hub found
[ 2.760070] hub 4-0:1.0: 2 ports detected
[ 2.978028] usb 5-2: new high-speed USB device number 2 using ehci-pci
[ 3.111532] usb 5-2: New USB device found, idVendor=148f, idProduct=5370
[ 3.111537] usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.111540] usb 5-2: Product: 802.11 n WLAN
[ 3.111543] usb 5-2: Manufacturer: TPlink
[ 3.111546] usb 5-2: SerialNumber: 1.0
[ 3.171063] PM: Marking nosave pages: [mem 0x0009f000-0x000fffff]
[ 3.171068] PM: Marking nosave pages: [mem 0xbfee0000-0xffffffff]
[ 3.171656] PM: Basic memory bitmaps created
[ 3.186278] PM: Basic memory bitmaps freed
[ 3.188775] PM: Starting manual resume from disk
[ 3.188779] PM: Hibernation image partition 8:3 present
[ 3.188780] PM: Looking for hibernation image.
[ 3.189836] PM: Image not found (code -22)
[ 3.189838] PM: Hibernation image not present or could not be loaded.
[ 3.230150] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 3.266061] usb 5-5: new high-speed USB device number 4 using ehci-pci
[ 3.301063] dracut: Checking ext4: /dev/disk/by-uuid/50be33c3-f160-43a4-82af-77bc8fa83ea2
[ 3.301212] dracut: issuing e2fsck -a /dev/disk/by-uuid/50be33c3-f160-43a4-82af-77bc8fa83ea2
[ 3.334980] dracut: /dev/disk/by-uuid/50be33c3-f160-43a4-82af-77bc8fa83ea2: clean, 64458/1921360 files, 740470/7680000 blocks
[ 3.336211] dracut: Mounting /dev/disk/by-uuid/50be33c3-f160-43a4-82af-77bc8fa83ea2 with -o acl,relatime,ro
[ 3.403033] usb 5-5: New USB device found, idVendor=0ac8, idProduct=3420
[ 3.403039] usb 5-5: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.403042] usb 5-5: Product: A4TECH USB2.0 PC Camera
[ 3.403045] usb 5-5: Manufacturer: A4TECH Corp.
[ 3.413529] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: acl
[ 3.466999] dracut: Mounted root filesystem /dev/sda1
[ 3.616162] dracut: Switching root
[ 3.617797] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist.
[ 3.661034] usb 4-2: new low-speed USB device number 2 using uhci_hcd
[ 3.928989] systemd[1]: systemd 208 running in system mode. (+PAM +LIBWRAP +AUDIT -SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ)
[ 4.025033] usb 4-2: New USB device found, idVendor=093a, idProduct=2510
[ 4.025038] usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 4.025041] usb 4-2: Product: USB Optical Mouse
[ 4.025044] usb 4-2: Manufacturer: PixArt
[ 4.067602] systemd[1]: Inserted module 'autofs4'
[ 4.116753] NET: Registered protocol family 10
[ 4.116972] systemd[1]: Inserted module 'ipv6'
[ 4.122081] systemd[1]: Set hostname to <localhost>.
[ 4.493041] usb 5-3: new high-speed USB device number 7 using ehci-pci
[ 4.588765] systemd[1]: Starting Replay Read-Ahead Data...
[ 5.512033] usb 5-3: new high-speed USB device number 12 using ehci-pci
[ 5.535318] ACPI: Requesting acpi_cpufreq
[ 5.538746] systemd[1]: Started Load legacy module configuration.
[ 5.618023] systemd[1]: Started File System Check on Root Device.
[ 5.618128] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 5.826767] systemd-udevd[494]: starting version 208
[ 5.860503] EXT4-fs (sda1): re-mounted. Opts: acl
[ 6.094196] IT8718 SuperIO detected.
[ 6.094445] parport_pc 00:07: reported by Plug and Play ACPI
[ 6.094483] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 6.095353] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 6.105898] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 6.105909] r8169 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
[ 6.111521] r8169 0000:03:00.0: irq 43 for MSI/MSI-X
[ 6.112131] r8169 0000:03:00.0 eth0: RTL8102e at 0xffffc9001079a000, 00:24:1d:90:ad:c4, XID 14a00000 IRQ 43
[ 6.113278] intel_rng: FWH not detected
[ 6.116152] i801_smbus 0000:00:1f.3: SMBus using PCI Interrupt
[ 6.120671] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \GP2C 1 (20130725/utaddress-251)
[ 6.120678] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 6.120695] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 6.123347] leds_ss4200: no LED devices found
[ 6.125269] microcode: CPU0 sig=0x1067a, pf=0x1, revision=0xa07
[ 6.141820] microcode: CPU1 sig=0x1067a, pf=0x1, revision=0xa07
[ 6.141879] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 6.166248] cfg80211: Calling CRDA to update world regulatory domain
[ 6.167489] snd_hda_intel 0000:00:1b.0: irq 44 for MSI/MSI-X
[ 6.169026] usb 5-3: new high-speed USB device number 15 using ehci-pci
[ 6.176111] systemd-udevd[511]: renamed network interface eth0 to enp3s0
[ 6.177694] ppdev: user-space parallel port driver
[ 6.179112] iTCO_vendor_support: vendor-support=0
[ 6.179243] gpio_ich: GPIO from 206 to 255 on gpio_ich
[ 6.179635] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
[ 6.179659] iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0460)
[ 6.180678] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=1)
[ 6.191169] SKU: Nid=0x0 sku_cfg=0x0000c603
[ 6.191173] SKU: port_connectivity=0x0
[ 6.191174] SKU: enable_pcbeep=0x1
[ 6.191176] SKU: check_sum=0x00000000
[ 6.191176] SKU: customization=0x00000000
[ 6.191177] SKU: external_amp=0x0
[ 6.191179] SKU: platform_type=0x0
[ 6.191179] SKU: swap=0x1
[ 6.191180] SKU: override=0x1
[ 6.191498] autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:line
[ 6.191499] speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 6.191500] hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[ 6.191501] mono: mono_out=0x0
[ 6.191502] dig-out=0x1e/0x0
[ 6.191503] inputs:
[ 6.191505] Rear Mic=0x18
[ 6.191506] Front Mic=0x19
[ 6.191507] Line=0x1a
[ 6.191508] CD=0x1c
[ 6.191510] realtek: Enabling init ASM_ID=0xc603 CODEC_ID=10ec0883
[ 6.195234] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input3
[ 6.202629] pci 0000:00:1e.0: setting latency timer to 64
[ 6.202751] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5392, rev 0223 detected
[ 6.206169] ieee80211 phy0: rt2800_init_eeprom: Error - Invalid RF chipset 0x5362 detected
[ 6.206171] ieee80211 phy0: rt2x00lib_probe_dev: Error - Failed to allocate device
[ 6.206451] input: HDA Intel Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 6.206514] input: HDA Intel Line Out as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[ 6.206554] input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6
[ 6.206594] input: HDA Intel Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input5
[ 6.206634] input: HDA Intel Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input4
[ 6.247250] cfg80211: World regulatory domain updated:
[ 6.247254] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 6.247255] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 6.247257] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 6.247258] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[ 6.247260] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 6.247261] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 6.247262] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 6.347352] hidraw: raw HID events driver (C) Jiri Kosina
[ 6.363340] usbcore: registered new interface driver usbhid
[ 6.363343] usbhid: USB HID core driver
[ 6.364286] input: PixArt USB Optical Mouse as /devices/pci0000:00/0000:00:1d.3/usb4/4-2/4-2:1.0/input/input9
[ 6.364364] hid-generic 0003:093A:2510.0001: input,hidraw0: USB HID v1.11 Mouse [PixArt USB Optical Mouse] on usb-0000:00:1d.3-2/input0
[ 6.464017] usb 5-3: new high-speed USB device number 16 using ehci-pci
[ 7.483043] usb 5-3: new high-speed USB device number 21 using ehci-pci
[ 7.778024] usb 5-3: new high-speed USB device number 22 using ehci-pci
[ 8.176414] Adding 4095996k swap on /dev/sda3. Priority:-1 extents:1 across:4095996k FS
[ 8.797027] usb 5-3: new high-speed USB device number 27 using ehci-pci
[ 9.092036] usb 5-3: new high-speed USB device number 28 using ehci-pci
[ 9.192528] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: acl
[ 9.236385] systemd-journald[444]: Received request to flush runtime journal from PID 1
[ 9.568031] usb 5-3: new high-speed USB device number 30 using ehci-pci
[ 9.663612] r8169 0000:03:00.0 enp3s0: link down
[ 9.664444] IPv6: ADDRCONF(NETDEV_UP): enp3s0: link is not ready
[ 9.863060] usb 5-3: new high-speed USB device number 31 using ehci-pci
[ 9.971028] systemd[1]: Received SIGRTMIN+21 from PID 240 (n/a).
[ 10.339027] usb 5-3: new high-speed USB device number 33 using ehci-pci
[ 10.636028] usb 5-3: new high-speed USB device number 34 using ehci-pci
[ 10.931027] usb 5-3: new high-speed USB device number 35 using ehci-pci
[ 11.226030] usb 5-3: new high-speed USB device number 36 using ehci-pci
[ 12.066174] usb 5-3: new high-speed USB device number 40 using ehci-pci
[ 13.270029] usb 5-3: new high-speed USB device number 46 using ehci-pci
[ 13.542035] usb 5-2: reset high-speed USB device number 2 using ehci-pci
[ 13.668660] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 5390, rev 0502 detected
[ 13.696784] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 5370 detected
[ 13.699639] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 13.699871] usbcore: registered new interface driver rt2800usb
[ 13.700030] Loading kernel module for a network device with CAP_SYS_MODULE (deprecated). Use CAP_NET_ADMIN and alias netdev-wlp0s29f7u2 instead.
[ 13.943027] usb 5-3: new high-speed USB device number 48 using ehci-pci
[ 14.604030] usb 5-3: new high-speed USB device number 51 using ehci-pci
[ 17.441024] usb 2-1: new full-speed USB device number 2 using uhci_hcd
[ 17.570035] usb 2-1: not running at top speed; connect to a high speed hub
[ 17.610035] usb 2-1: New USB device found, idVendor=0aec, idProduct=3260
[ 17.610042] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 17.610045] usb 2-1: Product: USB Storage Device
[ 17.610048] usb 2-1: Manufacturer: GENERIC
[ 17.610051] usb 2-1: SerialNumber: 200510251942096LD
[ 17.646934] media: Linux media interface: v0.10
[ 17.651287] systemd-udevd[504]: renamed network interface wlan0 to wlp0s29f7u2
[ 17.656141] Linux video capture interface: v2.00
[ 17.712082] cfg80211: Calling CRDA for country: GR
[ 17.717206] usb-storage 2-1:1.0: USB Mass Storage device detected
[ 17.718077] scsi2 : usb-storage 2-1:1.0
[ 17.718477] usbcore: registered new interface driver usb-storage
[ 17.722941] cfg80211: Regulatory domain changed to country: GR
[ 17.722945] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 17.722949] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 17.722951] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 17.722954] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 17.722957] cfg80211: (5490000 KHz - 5710000 KHz @ 80000 KHz), (N/A, 2700 mBm)
[ 17.722959] cfg80211: (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
[ 18.109186] ieee80211 phy1: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'
[ 18.152544] ieee80211 phy1: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.29
[ 18.358831] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u2: link is not ready
[ 18.615832] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u2: link is not ready
[ 18.654589] NET: Registered protocol family 17
[ 18.726055] scsi 2:0:0:0: Direct-Access GENERIC USB Storage-SMC I19B PQ: 0 ANSI: 0 CCS
[ 18.738050] scsi 2:0:0:1: Direct-Access GENERIC USB Storage-CFC I19B PQ: 0 ANSI: 0 CCS
[ 18.754077] scsi 2:0:0:2: Direct-Access GENERIC USB Storage-SDC I19B PQ: 0 ANSI: 0 CCS
[ 18.775106] scsi 2:0:0:3: Direct-Access GENERIC USB Storage-MSC I19B PQ: 0 ANSI: 0 CCS
[ 18.779366] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 18.797928] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 18.844592] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 18.867052] sd 2:0:0:1: [sdc] Attached SCSI removable disk
[ 18.884055] sd 2:0:0:2: [sdd] Attached SCSI removable disk
[ 18.895041] sd 2:0:0:3: [sde] Attached SCSI removable disk
[ 19.257377] Netfilter messages via NETLINK v0.30.
[ 19.270120] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 19.377253] xt_time: kernel timezone is +0300
[ 19.416121] ctnetlink v0.93: registering with nfnetlink.
[ 19.479440] ip_set: protocol 6
[ 19.589302] wlp0s29f7u2: authenticate with 00:13:33:84:db:37
[ 19.596560] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
[ 19.625800] wlp0s29f7u2: send auth to 00:13:33:84:db:37 (try 1/3)
[ 19.628520] wlp0s29f7u2: authenticated
[ 19.628554] rt2800usb 5-2:1.0 wlp0s29f7u2: disabling HT as WMM/QoS is not supported by the AP
[ 19.628556] rt2800usb 5-2:1.0 wlp0s29f7u2: disabling VHT as WMM/QoS is not supported by the AP
[ 19.629022] wlp0s29f7u2: associate with 00:13:33:84:db:37 (try 1/3)
[ 19.630928] wlp0s29f7u2: RX AssocResp from 00:13:33:84:db:37 (capab=0x411 status=0 aid=5)
[ 19.639170] wlp0s29f7u2: associated
[ 19.639200] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u2: link becomes ready
[ 19.921730] xt_addrtype: ipv6 does not support BROADCAST matching
[ 20.258441] xt_CT: No such helper "irc"
[ 20.270818] xt_CT: No such helper "irc-0"
[ 20.281000] xt_CT: No such helper "netbios-ns"
[ 20.298499] xt_CT: No such helper "snmp"
[ 20.310992] xt_CT: No such helper "pptp"
[ 20.414859] Bridge firewalling registered
[ 20.647079] u32 classifier
[ 20.647083] Actions configured
[ 22.026873] ipt_ULOG: ULOG is deprecated and it will be removed soon, use NFLOG instead
[ 22.377513] netfilter PSD loaded - (c) astaro AG
[ 22.378926] IFWLOG: register target
[ 67.675613] usbcore: registered new interface driver snd-usb-audio
[ 67.675616] uvcvideo: Found UVC 1.00 device A4TECH USB2.0 PC Camera (0ac8:3420)
[ 67.679203] input: A4TECH USB2.0 PC Camera as /devices/pci0000:00/0000:00:1d.7/usb5/5-5/5-5:1.0/input/input10
[ 67.679376] usbcore: registered new interface driver uvcvideo
[ 67.679379] USB Video Class driver (1.1.1)
[ 214.822986] cfg80211: Calling CRDA to update world regulatory domain
[ 214.826050] cfg80211: World regulatory domain updated:
[ 214.826055] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 214.826058] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 214.826061] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 214.826064] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[ 214.826066] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 214.826069] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 214.826072] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 214.826087] cfg80211: Calling CRDA for country: GR
[ 214.828529] cfg80211: Regulatory domain changed to country: GR
[ 214.828533] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 214.828537] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 214.828539] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 214.828542] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 214.828545] cfg80211: (5490000 KHz - 5710000 KHz @ 80000 KHz), (N/A, 2700 mBm)
[ 214.828547] cfg80211: (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
[ 215.861301] wlp0s29f7u2: authenticate with 00:13:33:84:db:37
[ 215.878967] wlp0s29f7u2: send auth to 00:13:33:84:db:37 (try 1/3)
[ 215.916101] wlp0s29f7u2: send auth to 00:13:33:84:db:37 (try 2/3)
[ 215.952223] wlp0s29f7u2: send auth to 00:13:33:84:db:37 (try 3/3)
[ 215.982722] wlp0s29f7u2: authentication with 00:13:33:84:db:37 timed out
[ 221.845801] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u2: link is not ready
[ 222.865842] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 12 in queue 0
[ 222.865863] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 12 in queue 0
[ 222.865867] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 12 in queue 0
[ 234.680311] wlp0s29f7u2: authenticate with 00:13:33:84:db:37
[ 234.697974] wlp0s29f7u2: send auth to 00:13:33:84:db:37 (try 1/3)
[ 234.699354] wlp0s29f7u2: authenticated
[ 234.699371] rt2800usb 5-2:1.0 wlp0s29f7u2: disabling HT as WMM/QoS is not supported by the AP
[ 234.699375] rt2800usb 5-2:1.0 wlp0s29f7u2: disabling VHT as WMM/QoS is not supported by the AP
[ 234.700012] wlp0s29f7u2: associate with 00:13:33:84:db:37 (try 1/3)
[ 234.701852] wlp0s29f7u2: RX AssocResp from 00:13:33:84:db:37 (capab=0x411 status=0 aid=5)
[ 234.708597] wlp0s29f7u2: associated
[ 234.708623] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u2: link becomes ready
[ 542.530059] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 8 in queue 2
[ 542.530082] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 8 in queue 2
[ 542.530087] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 8 in queue 2
[ 542.542430] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 9 in queue 2
[ 542.542445] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 9 in queue 2
[ 542.542450] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 9 in queue 2
[ 542.553684] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 10 in queue 2
[ 542.553699] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 10 in queue 2
[ 542.610698] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 15 in queue 2
[ 542.610704] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 15 in queue 2
[ 542.621930] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 0 in queue 2
[ 542.621942] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 0 in queue 2
[ 542.621946] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 0 in queue 2
[ 542.633182] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 1 in queue 2
[ 542.633195] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 1 in queue 2
[ 542.633201] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 1 in queue 2
[ 542.641055] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 2 in queue 2
[ 542.641075] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 2 in queue 2
[ 542.641078] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 2 in queue 2
[ 542.652306] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 3 in queue 2
[ 542.652318] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 3 in queue 2
[ 542.652322] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 3 in queue 2
[ 542.679433] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[ 542.737686] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[ 542.737803] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[ 542.737929] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[ 542.738472] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[ 542.738477] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[ 542.738479] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[ 542.738557] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[ 542.738682] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[ 542.738802] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[ 542.739631] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[ 542.739635] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[ 611.882967] cfg80211: Calling CRDA to update world regulatory domain
[ 611.886053] cfg80211: World regulatory domain updated:
[ 611.886058] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 611.886061] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 611.886064] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 611.886067] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[ 611.886070] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 611.886072] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 611.886075] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 611.886090] cfg80211: Calling CRDA for country: GR
[ 611.888493] cfg80211: Regulatory domain changed to country: GR
[ 611.888497] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 611.888500] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 611.888503] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 611.888506] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 611.888509] cfg80211: (5490000 KHz - 5710000 KHz @ 80000 KHz), (N/A, 2700 mBm)
[ 611.888511] cfg80211: (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
[ 612.922304] wlp0s29f7u2: authenticate with 00:13:33:84:db:37
[ 612.939956] wlp0s29f7u2: send auth to 00:13:33:84:db:37 (try 1/3)
[ 612.965836] wlp0s29f7u2: send auth to 00:13:33:84:db:37 (try 2/3)
[ 613.009839] wlp0s29f7u2: send auth to 00:13:33:84:db:37 (try 3/3)
[ 613.054958] wlp0s29f7u2: authentication with 00:13:33:84:db:37 timed out
[ 619.096784] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u2: link is not ready
[ 620.039323] wlp0s29f7u2: authenticate with 00:13:33:84:db:37
[ 620.056956] wlp0s29f7u2: send auth to 00:13:33:84:db:37 (try 1/3)
[ 620.058342] wlp0s29f7u2: authenticated
[ 620.058361] rt2800usb 5-2:1.0 wlp0s29f7u2: disabling HT as WMM/QoS is not supported by the AP
[ 620.058365] rt2800usb 5-2:1.0 wlp0s29f7u2: disabling VHT as WMM/QoS is not supported by the AP
[ 620.059013] wlp0s29f7u2: associate with 00:13:33:84:db:37 (try 1/3)
[ 620.060959] wlp0s29f7u2: RX AssocResp from 00:13:33:84:db:37 (capab=0x411 status=0 aid=5)
[ 620.067706] wlp0s29f7u2: associated
[ 620.067718] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u2: link becomes ready
[ 620.170201] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 0 in queue 2
[ 620.170214] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 0 in queue 2
[ 620.170219] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 0 in queue 2
[ 660.172965] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 10 in queue 2
[ 681.081100] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 5 in queue 2
[ 681.081104] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 5 in queue 2
[ 681.120351] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[ 681.120471] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[ 681.120595] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[[ 681.184968] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[ 681.185094] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[ 682.908471] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 9 in queue 2
[ 682.908491] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 9 in queue 2
[ 682.908495] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 9 in queue 2
[ 682.910717] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 10 in queue 2
[ 682.944484] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 7 in queue 2
[ 682.978600] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[ 682.978717] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[ 682.978845] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[ 682.994970] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[ 682.995097] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[ 740.003051] usb 5-2: USB disconnect, device number 2
[ 741.114013] ieee80211 phy1: rt2800_wait_wpdma_ready: Error - WPDMA TX/RX busy [0xffffffff]
[ 741.118029] wlp0s29f7u2: deauthenticating from 00:13:33:84:db:37 by local choice (reason=3)
[ 741.134676] cfg80211: Calling CRDA to update world regulatory domain
[ 741.137846] cfg80211: World regulatory domain updated:
[ 741.137851] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 741.137854] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 741.137857] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 741.137860] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[ 741.137862] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 741.137865] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 741.137868] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 741.137884] cfg80211: Calling CRDA for country: GR
[ 741.139396] Loading kernel module for a network device with CAP_SYS_MODULE (deprecated). Use CAP_NET_ADMIN and alias netdev-wlp0s29f7u2 instead.
[ 741.143965] Loading kernel module for a network device with CAP_SYS_MODULE (deprecated). Use CAP_NET_ADMIN and alias netdev-wlp0s29f7u2 instead.
[ 741.144645] cfg80211: Regulatory domain changed to country: GR
[ 741.144649] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 741.144652] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 741.144655] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 741.144658] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 741.144661] cfg80211: (5490000 KHz - 5710000 KHz @ 80000 KHz), (N/A, 2700 mBm)
[ 741.144663] cfg80211: (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
[ 741.152345] Loading kernel module for a network device with CAP_SYS_MODULE (deprecated). Use CAP_NET_ADMIN and alias netdev-wlp0s29f7u2 instead.
[ 741.274739] Loading kernel module for a network device with CAP_SYS_MODULE (deprecated). Use CAP_NET_ADMIN and alias netdev-wlp0s29f7u2 instead.
[ 741.277215] Loading kernel module for a network device with CAP_SYS_MODULE (deprecated). Use CAP_NET_ADMIN and alias netdev-wlp0s29f7u2 instead.
[ 760.580542] Loading kernel module for a network device with CAP_SYS_MODULE (deprecated). Use CAP_NET_ADMIN and alias netdev-wlp0s29f7u2 instead.
[ 760.583071] Loading kernel module for a network device with CAP_SYS_MODULE (deprecated). Use CAP_NET_ADMIN and alias netdev-wlp0s29f7u2 instead.
[ 797.174026] usb 5-2: new high-speed USB device number 65 using ehci-pci
[ 797.307518] usb 5-2: New USB device found, idVendor=148f, idProduct=5370
[ 797.307524] usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 797.307527] usb 5-2: Product: 802.11 n WLAN
[ 797.307530] usb 5-2: Manufacturer: TPlink
[ 797.307533] usb 5-2: SerialNumber: 1.0
[ 797.412031] usb 5-2: reset high-speed USB device number 65 using ehci-pci
[ 797.538646] ieee80211 phy2: rt2x00_set_rt: Info - RT chipset 5390, rev 0502 detected
[ 797.566771] ieee80211 phy2: rt2x00_set_rf: Info - RF chipset 5370 detected
[ 797.567153] ieee80211 phy2: Selected rate control algorithm 'minstrel_ht'
[ 797.581173] systemd-udevd[4248]: renamed network interface wlan0 to wlp0s29f7u2
[ 797.662030] ieee80211 phy2: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'
[ 797.662076] ieee80211 phy2: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.29
[ 797.870448] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u2: link is not ready
[ 798.126809] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u2: link is not ready
[ 799.083312] wlp0s29f7u2: authenticate with 00:13:33:84:db:37
[ 799.113775] wlp0s29f7u2: send auth to 00:13:33:84:db:37 (try 1/3)
[ 799.115156] wlp0s29f7u2: authenticated
[ 799.115172] rt2800usb 5-2:1.0 wlp0s29f7u2: disabling HT as WMM/QoS is not supported by the AP
[ 799.115176] rt2800usb 5-2:1.0 wlp0s29f7u2: disabling VHT as WMM/QoS is not supported by the AP
[ 799.116016] wlp0s29f7u2: associate with 00:13:33:84:db:37 (try 1/3)
[ 799.117902] wlp0s29f7u2: RX AssocResp from 00:13:33:84:db:37 (capab=0x411 status=0 aid=5)
[ 799.124648] wlp0s29f7u2: associated
[ 799.124672] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u2: link becomes ready
Intel Core i5-6300U CPU @ 2.40GHz ‖ RAM 7860 MiB ‖ HP 8079 - HP HP EliteBook 840 G3
Intel Skylake GT2 [HD Graphics 520] [8086:1916] {i915}
wlp2s0: Intel Wireless 8260 [8086:24f3] (rev 3a) ⋮ enp0s31f6: Intel Ethernet Connection I219-LM [8086:156f] (rev 21)
Intel Skylake GT2 [HD Graphics 520] [8086:1916] {i915}
wlp2s0: Intel Wireless 8260 [8086:24f3] (rev 3a) ⋮ enp0s31f6: Intel Ethernet Connection I219-LM [8086:156f] (rev 21)
Re: προβλημα με wi-fi
Κώδικας: Επιλογή όλων
lpcidrake
Κώδικας: Επιλογή όλων
command not found
Intel Core i5-6300U CPU @ 2.40GHz ‖ RAM 7860 MiB ‖ HP 8079 - HP HP EliteBook 840 G3
Intel Skylake GT2 [HD Graphics 520] [8086:1916] {i915}
wlp2s0: Intel Wireless 8260 [8086:24f3] (rev 3a) ⋮ enp0s31f6: Intel Ethernet Connection I219-LM [8086:156f] (rev 21)
Intel Skylake GT2 [HD Graphics 520] [8086:1916] {i915}
wlp2s0: Intel Wireless 8260 [8086:24f3] (rev 3a) ⋮ enp0s31f6: Intel Ethernet Connection I219-LM [8086:156f] (rev 21)
Re: προβλημα με wi-fi
Κώδικας: Επιλογή όλων
rt2800pci : Ralink corp.|Device 5362 [NETWORK_OTHER]
r8169 : Realtek Semiconductor Co., Ltd.|RTL8101E/RTL8102E PCI Express Fast Ethernet controller [NETWORK_ETHERNET] (rev: 02)
Card:NVIDIA GeForce 8100 to GeForce 360: NVIDIA Corporation|G96 [GeForce 9500 GT] [DISPLAY_VGA] (rev: a1)
i2c_i801 : Intel Corporation|NM10/ICH7 Family SMBus Controller [SERIAL_SMBUS] (rev: 01)
ata_piix : Intel Corporation|NM10/ICH7 Family SATA Controller [IDE mode] [STORAGE_IDE] (rev: 01)
intel_rng : Intel Corporation|82801GB/GR (ICH7 Family) LPC Interface Bridge [BRIDGE_ISA] (rev: 01)
unknown : Intel Corporation|82801 PCI Bridge [BRIDGE_PCI] (rev: e1)
ehci_pci : Intel Corporation|NM10/ICH7 Family USB2 EHCI Controller [SERIAL_USB] (rev: 01)
uhci_hcd : Intel Corporation|NM10/ICH7 Family USB UHCI Controller #4 [SERIAL_USB] (rev: 01)
uhci_hcd : Intel Corporation|NM10/ICH7 Family USB UHCI Controller #3 [SERIAL_USB] (rev: 01)
uhci_hcd : Intel Corporation|NM10/ICH7 Family USB UHCI Controller #2 [SERIAL_USB] (rev: 01)
uhci_hcd : Intel Corporation|NM10/ICH7 Family USB UHCI Controller #1 [SERIAL_USB] (rev: 01)
shpchp : Intel Corporation|NM10/ICH7 Family PCI Express Port 2 [BRIDGE_PCI] (rev: 01)
shpchp : Intel Corporation|NM10/ICH7 Family PCI Express Port 1 [BRIDGE_PCI] (rev: 01)
snd_hda_intel : Intel Corporation|NM10/ICH7 Family High Definition Audio Controller [MULTIMEDIA_AUDIO_DEV] (rev: 01)
shpchp : Intel Corporation|82G33/G31/P35/P31 Express PCI Express Root Port [BRIDGE_PCI] (rev: 10)
unknown : Intel Corporation|82G33/G31/P35/P31 Express DRAM Controller [BRIDGE_HOST] (rev: 10)
hub : Linux 3.12.13-desktop-2.mga4 ehci_hcd|EHCI Host Controller [Hub|Unused|Full speed (or root) hub]
rt2800usb : TPlink|802.11 n WLAN
uvcvideo : A4TECH Corp.|A4TECH USB2.0 PC Camera [Video|Video Control]
hub : Linux 3.12.13-desktop-2.mga4 uhci_hcd|UHCI Host Controller [Hub|Unused|Full speed (or root) hub]
usbhid : PixArt|USB Optical Mouse [Human Interface Device|Boot Interface Subclass|Mouse]
hub : Linux 3.12.13-desktop-2.mga4 uhci_hcd|UHCI Host Controller [Hub|Unused|Full speed (or root) hub]
hub : Linux 3.12.13-desktop-2.mga4 uhci_hcd|UHCI Host Controller [Hub|Unused|Full speed (or root) hub]
usb_storage : GENERIC|USB Storage Device [Mass Storage|SCSI|Bulk-Only]
hub : Linux 3.12.13-desktop-2.mga4 uhci_hcd|UHCI Host Controller [Hub|Unused|Full speed (or root) hub]
hid_generic : PixArt USB Optical Mouse
Intel Core i5-6300U CPU @ 2.40GHz ‖ RAM 7860 MiB ‖ HP 8079 - HP HP EliteBook 840 G3
Intel Skylake GT2 [HD Graphics 520] [8086:1916] {i915}
wlp2s0: Intel Wireless 8260 [8086:24f3] (rev 3a) ⋮ enp0s31f6: Intel Ethernet Connection I219-LM [8086:156f] (rev 21)
Intel Skylake GT2 [HD Graphics 520] [8086:1916] {i915}
wlp2s0: Intel Wireless 8260 [8086:24f3] (rev 3a) ⋮ enp0s31f6: Intel Ethernet Connection I219-LM [8086:156f] (rev 21)
- dglent
- Δημοσιεύσεις: 1069
- Εγγραφή: Τετ Ιουν 01, 2011 05:42 am
- Τοποθεσία: Γαλλία
- Has thanked: 6 φορές
Re: προβλημα με wi-fi
Δες μήπως χρειάζεται αυτό:
https://forums.mageia.org/en/viewtopic.php?f=8&t=5845
https://forums.mageia.org/en/viewtopic.php?f=8&t=5845
Re: προβλημα με wi-fi
εμένα το lsmod μου δειχνει αυτο
έδωσα και
echo "blacklist asus_wmi" >> /etc/modprobe.d/blacklist-mga.conf
εκανα και μια επανεκκινηση αλλα δεν αλλαξε τιποτα
Κώδικας: Επιλογή όλων
Module Size Used by
ipt_IFWLOG 12622 2
ipt_psd 57587 1
ipt_rpfilter 12546 0
xt_realm 12498 0
cls_basic 12946 0
cls_flow 17125 0
cls_fw 12904 0
cls_u32 17137 0
sch_fq_codel 17545 0
sch_tbf 13137 0
sch_prio 13152 0
sch_hfsc 22164 0
sch_htb 22278 0
sch_ingress 12866 0
sch_sfq 21416 0
bridge 110673 0
stp 12976 1 bridge
llc 14552 2 stp,bridge
ip6t_MASQUERADE 12768 0
xt_CHECKSUM 12549 0
ip6t_rpfilter 12546 0
xt_statistic 12601 0
xt_CT 12956 36
xt_LOG 17717 10
xt_connlimit 12636 0
xt_addrtype 12635 4
ip_set_hash_ip 27260 2
xt_comment 12504 48
xt_recent 18498 2
ipt_ULOG 14273 0
ipt_REJECT 12541 4
ipt_MASQUERADE 12880 0
ipt_ECN 12529 0
ipt_CLUSTERIP 13508 0
ipt_ah 12806 0
nf_nat_tftp 12489 0
nf_nat_snmp_basic 17302 0
nf_conntrack_snmp 12857 3 nf_nat_snmp_basic
nf_nat_sip 17152 0
nf_nat_pptp 13115 0
nf_nat_proto_gre 13009 1 nf_nat_pptp
xt_nat 12681 0
ip6table_nat 13015 0
nf_nat_ipv6 13279 1 ip6table_nat
nf_nat_irc 12723 0
xt_set 13181 2
ip_set 36597 2 ip_set_hash_ip,xt_set
nf_nat_h323 17720 0
nf_nat_ftp 12770 0
nf_nat_amanda 12491 0
nf_conntrack_tftp 13121 5 nf_nat_tftp
nf_conntrack_sane 13143 4
nf_conntrack_sip 29764 5 nf_nat_sip
nf_conntrack_proto_udplite 13281 0
nf_conntrack_proto_sctp 18822 0
nf_conntrack_pptp 19258 3 nf_nat_pptp
nf_conntrack_proto_gre 14434 1 nf_conntrack_pptp
ts_kmp 12605 5
nf_conntrack_netlink 36189 0
nf_conntrack_netbios_ns 12665 2
nf_conntrack_broadcast 12589 2 nf_conntrack_netbios_ns,nf_conntrack_snmp
nf_conntrack_amanda 13041 5 nf_nat_amanda
nf_conntrack_irc 13518 3 nf_nat_irc
nf_conntrack_h323 73845 9 nf_nat_h323
nf_conntrack_ftp 18638 5 nf_nat_ftp
xt_TPROXY 17356 0
xt_time 12661 0
xt_TCPMSS 12707 0
xt_tcpmss 12501 0
xt_sctp 12853 0
xt_policy 12582 0
xt_pkttype 12504 0
xt_physdev 12587 0
xt_owner 12534 0
xt_NFQUEUE 12776 0
xt_NFLOG 12537 0
nfnetlink_log 17879 1 xt_NFLOG
xt_multiport 12798 8
xt_mark 12563 2
xt_mac 12492 0
xt_limit 12711 0
xt_length 12536 0
xt_iprange 12783 0
xt_helper 12583 0
xt_hashlimit 17569 0
xt_DSCP 12629 0
xt_dscp 12597 0
xt_dccp 12606 0
xt_connmark 12755 0
xt_CLASSIFY 12507 0
ip6t_REJECT 12939 4
xt_AUDIT 12678 0
xt_tcpudp 12884 56
nf_conntrack_ipv6 18894 23
xt_state 12578 0
nf_defrag_ipv6 34651 2 xt_TPROXY,nf_conntrack_ipv6
iptable_raw 12678 1
iptable_nat 13011 0
nf_nat_ipv4 13263 1 iptable_nat
nf_nat 21568 15 nf_nat_ftp,nf_nat_irc,nf_nat_sip,nf_nat_amanda,ipt_MASQUERADE,nf_nat_proto_gre,ip6t_MASQUERADE,nf_nat_h323,nf_nat_ipv4,nf_nat_ipv6,nf_nat_pptp,nf_nat_tftp,xt_nat,ip6table_nat,iptable_nat
xt_conntrack 12760 17
nf_conntrack_ipv4 15012 32
nf_defrag_ipv4 12758 2 xt_TPROXY,nf_conntrack_ipv4
ip6table_raw 12683 1
nf_conntrack 92796 39 nf_nat_ftp,nf_nat_irc,nf_nat_sip,nf_nat_amanda,xt_CT,nf_nat_snmp_basic,nf_conntrack_netbios_ns,nf_conntrack_proto_gre,xt_helper,ipt_MASQUERADE,nf_conntrack_proto_udplite,nf_nat,ip6t_MASQUERADE,xt_state,xt_connlimit,nf_nat_h323,nf_nat_ipv4,nf_nat_ipv6,nf_nat_pptp,nf_nat_tftp,xt_conntrack,nf_conntrack_amanda,ipt_CLUSTERIP,nf_conntrack_proto_sctp,nf_conntrack_netlink,ip6table_nat,nf_conntrack_broadcast,xt_connmark,nf_conntrack_ftp,nf_conntrack_irc,nf_conntrack_sip,iptable_nat,nf_conntrack_h323,nf_conntrack_ipv4,nf_conntrack_ipv6,nf_conntrack_pptp,nf_conntrack_sane,nf_conntrack_snmp,nf_conntrack_tftp
ip6table_mangle 12700 1
iptable_mangle 12695 1
nfnetlink 14606 3 nfnetlink_log,ip_set,nf_conntrack_netlink
iptable_filter 12810 1
ip_tables 27239 4 iptable_filter,iptable_mangle,iptable_nat,iptable_raw
ip6table_filter 12815 1
ip6_tables 27025 4 ip6table_filter,ip6table_mangle,ip6table_nat,ip6table_raw
x_tables 34059 59 xt_physdev,xt_pkttype,ip6table_filter,xt_statistic,xt_DSCP,xt_dccp,xt_dscp,xt_iprange,xt_mark,xt_sctp,xt_time,xt_CT,xt_helper,ip6table_mangle,ip6t_rpfilter,xt_length,xt_comment,ipt_ULOG,xt_policy,xt_CHECKSUM,xt_recent,ip_tables,xt_tcpmss,xt_tcpudp,ipt_MASQUERADE,ipt_ah,xt_AUDIT,xt_NFQUEUE,xt_NFLOG,ip6t_MASQUERADE,xt_limit,xt_owner,xt_realm,xt_state,ipt_rpfilter,xt_connlimit,xt_conntrack,xt_LOG,xt_mac,xt_nat,xt_set,ipt_IFWLOG,ipt_CLUSTERIP,xt_hashlimit,xt_multiport,iptable_filter,ip6table_raw,xt_CLASSIFY,xt_TCPMSS,xt_TPROXY,xt_connmark,ipt_REJECT,iptable_mangle,ipt_ECN,ipt_psd,ip6_tables,xt_addrtype,iptable_raw,ip6t_REJECT
af_packet 35649 4
usb_storage 62062 0
uvcvideo 80968 0
videobuf2_vmalloc 13216 1 uvcvideo
videobuf2_memops 13362 1 videobuf2_vmalloc
videobuf2_core 40625 1 uvcvideo
snd_usb_audio 149112 1
videodev 134653 2 uvcvideo,videobuf2_core
snd_usbmidi_lib 25070 1 snd_usb_audio
snd_rawmidi 30427 1 snd_usbmidi_lib
media 21895 2 uvcvideo,videodev
snd_seq_device 14497 1 snd_rawmidi
arc4 12608 2
rt2800usb 27034 0
rt2x00usb 20742 1 rt2800usb
hid_generic 12548 0
usbhid 48429 0
hid 105788 2 hid_generic,usbhid
rt2800pci 18719 0
rt2800lib 88813 2 rt2800pci,rt2800usb
rt2x00pci 13287 1 rt2800pci
rt2x00mmio 13603 1 rt2800pci
rt2x00lib 55306 6 rt2x00pci,rt2x00usb,rt2800lib,rt2800pci,rt2800usb,rt2x00mmio
eeprom_93cx6 13344 1 rt2800pci
mac80211 516025 4 rt2x00lib,rt2x00pci,rt2x00usb,rt2800lib
snd_hda_codec_realtek 56661 1
iTCO_wdt 13480 0
gpio_ich 13476 0
iTCO_vendor_support 13718 1 iTCO_wdt
snd_hda_intel 52267 5
cfg80211 474802 2 mac80211,rt2x00lib
ppdev 17635 0
snd_hda_codec 192906 2 snd_hda_codec_realtek,snd_hda_intel
coretemp 13435 0
snd_hwdep 17698 2 snd_usb_audio,snd_hda_codec
snd_pcm 102078 3 snd_usb_audio,snd_hda_codec,snd_hda_intel
microcode 19560 0
lpc_ich 21080 0
serio_raw 13413 0
i2c_i801 22443 0
crc_ccitt 12707 1 rt2800lib
rfkill 22676 2 cfg80211
rng_core 13395 0
r8169 71677 0
snd_page_alloc 18710 2 snd_pcm,snd_hda_intel
snd_timer 29378 1 snd_pcm
mii 13934 1 r8169
snd 83274 22 snd_hda_codec_realtek,snd_usb_audio,snd_hwdep,snd_timer,snd_pcm,snd_rawmidi,snd_usbmidi_lib,snd_hda_codec,snd_hda_intel,snd_seq_device
soundcore 15047 1 snd
shpchp 37032 0
parport_pc 41374 0
parport 42264 2 ppdev,parport_pc
evdev 17787 15
cpufreq_ondemand 20254 2
cpufreq_conservative 15314 0
cpufreq_powersave 12618 0
acpi_cpufreq 19790 0
processor 31527 1 acpi_cpufreq
ipv6 357086 54 ip6table_mangle,ip6t_rpfilter,bridge,nf_defrag_ipv6,ip6t_MASQUERADE,nf_nat_ipv6,ip6table_nat,xt_TPROXY,ip6t_REJECT,nf_conntrack_ipv6
autofs4 38674 2
ehci_pci 12905 0
ehci_hcd 71045 1 ehci_pci
uhci_hcd 32230 0
usbcore 228902 10 uhci_hcd,snd_usb_audio,uvcvideo,rt2x00usb,usb_storage,rt2800usb,snd_usbmidi_lib,ehci_hcd,ehci_pci,usbhid
sr_mod 22411 0
usb_common 13057 1 usbcore
nouveau 952644 2
button 13871 1 nouveau
video 19268 1 nouveau
mxm_wmi 13021 1 nouveau
wmi 19177 2 mxm_wmi,nouveau
i2c_algo_bit 13413 1 nouveau
drm_kms_helper 44214 1 nouveau
ttm 83917 1 nouveau
drm 297706 4 ttm,drm_kms_helper,nouveau
i2c_core 40643 6 drm,i2c_i801,drm_kms_helper,i2c_algo_bit,nouveau,videodev
ide_pci_generic 12866 0
ide_core 117183 1 ide_pci_generic
ata_generic 12910 0
pata_acpi 13038 0
ata_piix 35038 4
echo "blacklist asus_wmi" >> /etc/modprobe.d/blacklist-mga.conf
εκανα και μια επανεκκινηση αλλα δεν αλλαξε τιποτα
Intel Core i5-6300U CPU @ 2.40GHz ‖ RAM 7860 MiB ‖ HP 8079 - HP HP EliteBook 840 G3
Intel Skylake GT2 [HD Graphics 520] [8086:1916] {i915}
wlp2s0: Intel Wireless 8260 [8086:24f3] (rev 3a) ⋮ enp0s31f6: Intel Ethernet Connection I219-LM [8086:156f] (rev 21)
Intel Skylake GT2 [HD Graphics 520] [8086:1916] {i915}
wlp2s0: Intel Wireless 8260 [8086:24f3] (rev 3a) ⋮ enp0s31f6: Intel Ethernet Connection I219-LM [8086:156f] (rev 21)
Re: προβλημα με wi-fi
δώσε
Κώδικας: Επιλογή όλων
lspci -knn | grep -EiA3 net
Κώδικας: Επιλογή όλων
inxi -nz
Re: προβλημα με wi-fi
Κώδικας: Επιλογή όλων
lspci -knn | grep -EiA3 net
Κώδικας: Επιλογή όλων
03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 02)
Subsystem: Gigabyte Technology Co., Ltd Device [1458:e000]
Kernel driver in use: r8169
Kernel modules: r8169
04:01.0 Network controller [0280]: Ralink corp. Device [1814:5362]
Subsystem: Ralink corp. Device [1814:5362]
Kernel modules: rt2800pci
Κώδικας: Επιλογή όλων
inxi -nz
Κώδικας: Επιλογή όλων
Network: Card-1: Realtek RTL8101E/RTL8102E PCI Express Fast Ethernet controller driver: r8169
IF: enp3s0 state: down mac: <filter>
Card-2: Ralink Device 5362
IF: N/A state: N/A speed: N/A duplex: N/A mac: N/A
Card-3: Ralink RT5370 Wireless Adapter driver: rt2800usb
IF: wlp0s29f7u2 state: up mac: <filter>
http://www.tp-link.com/en/products/deta ... =TL-WN727N
Intel Core i5-6300U CPU @ 2.40GHz ‖ RAM 7860 MiB ‖ HP 8079 - HP HP EliteBook 840 G3
Intel Skylake GT2 [HD Graphics 520] [8086:1916] {i915}
wlp2s0: Intel Wireless 8260 [8086:24f3] (rev 3a) ⋮ enp0s31f6: Intel Ethernet Connection I219-LM [8086:156f] (rev 21)
Intel Skylake GT2 [HD Graphics 520] [8086:1916] {i915}
wlp2s0: Intel Wireless 8260 [8086:24f3] (rev 3a) ⋮ enp0s31f6: Intel Ethernet Connection I219-LM [8086:156f] (rev 21)