προβλημα με wi-fi

Άβαταρ μέλους
airmaik
Δημοσιεύσεις: 637
Εγγραφή: Τρί Ιουν 07, 2011 16:44 pm

προβλημα με wi-fi

Δημοσίευση από airmaik » Παρ Απρ 18, 2014 07:47 am

εχω παρει μια ασυρματη καρτα που κουμπώνει σε pci

αφου την εβαλα και πα στα δικτυα μου βγαζει την παρακάτω εικόνα

https://www.flickr.com/photos/99709873@ ... otostream/

το πακέτο firmware-Ralink το έχω εγκαταστήσει
Intel Core i5-6300U CPU @ 2.40GHz ‖ RAM 7860 MiB ‖ HP 8079 - HP HP EliteBook 840 G3
Intel Skylake GT2 [HD Graphics 520] [8086:1916] {i915}
wlp2s0: Intel Wireless 8260 [8086:24f3] (rev 3a) ⋮ enp0s31f6: Intel Ethernet Connection I219-LM [8086:156f] (rev 21)

Άβαταρ μέλους
dglent
Δημοσιεύσεις: 934
Εγγραφή: Τετ Ιουν 01, 2011 05:42 am
Τοποθεσία: Γαλλία

Re: προβλημα με wi-fi

Δημοσίευση από dglent » Παρ Απρ 18, 2014 08:04 am

Γράψε και το μοντέλο της κάρτας και ποιο άρθρωμα χρησιμοποιεί μήπως βρούμε πληροφορίες και σε ξένα φόρουμ
και την έξοδο των εντολών:
lpcidrake
dmesg

Άβαταρ μέλους
airmaik
Δημοσιεύσεις: 637
Εγγραφή: Τρί Ιουν 07, 2011 16:44 pm

Re: προβλημα με wi-fi

Δημοσίευση από airmaik » Παρ Απρ 18, 2014 08:15 am

αυτο ειναι το μοντελο

http://www.netis-systems.com/en/product ... 1DA-PEvBDU

δίνω

Κώδικας: Επιλογή όλων

dmesg

Κώδικας: Επιλογή όλων

[    0.136203] pci 0000:00:1f.2: reg 0x14: [io  0x0000-0x0003]
[    0.136210] pci 0000:00:1f.2: reg 0x18: [io  0x0000-0x0007]
[    0.136216] pci 0000:00:1f.2: reg 0x1c: [io  0x0000-0x0003]
[    0.136223] pci 0000:00:1f.2: reg 0x20: [io  0xf000-0xf00f]
[    0.136252] pci 0000:00:1f.2: PME# supported from D3hot
[    0.136308] pci 0000:00:1f.3: [8086:27da] type 00 class 0x0c0500
[    0.136352] pci 0000:00:1f.3: reg 0x20: [io  0x0500-0x051f]
[    0.136458] pci 0000:01:00.0: [10de:0640] type 00 class 0x030000
[    0.136467] pci 0000:01:00.0: reg 0x10: [mem 0xe2000000-0xe2ffffff]
[    0.136476] pci 0000:01:00.0: reg 0x14: [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.136485] pci 0000:01:00.0: reg 0x1c: [mem 0xe0000000-0xe1ffffff 64bit]
[    0.136492] pci 0000:01:00.0: reg 0x24: [io  0xc000-0xc07f]
[    0.136498] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0007ffff pref]
[    0.136563] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.136566] pci 0000:00:01.0:   bridge window [io  0xc000-0xcfff]
[    0.136568] pci 0000:00:01.0:   bridge window [mem 0xe0000000-0xe3ffffff]
[    0.136572] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.136614] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.136617] pci 0000:00:1c.0:   bridge window [io  0xb000-0xbfff]
[    0.136679] pci 0000:03:00.0: [10ec:8136] type 00 class 0x020000
[    0.136694] pci 0000:03:00.0: reg 0x10: [io  0xd000-0xd0ff]
[    0.136719] pci 0000:03:00.0: reg 0x18: [mem 0xe5010000-0xe5010fff 64bit pref]
[    0.136735] pci 0000:03:00.0: reg 0x20: [mem 0xe5000000-0xe500ffff 64bit pref]
[    0.136746] pci 0000:03:00.0: reg 0x30: [mem 0x00000000-0x0001ffff pref]
[    0.136804] pci 0000:03:00.0: supports D1 D2
[    0.136805] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.138021] pci 0000:00:1c.1: PCI bridge to [bus 03]
[    0.138027] pci 0000:00:1c.1:   bridge window [io  0xd000-0xdfff]
[    0.138032] pci 0000:00:1c.1:   bridge window [mem 0xe4000000-0xe4ffffff]
[    0.138039] pci 0000:00:1c.1:   bridge window [mem 0xe5000000-0xe50fffff 64bit pref]
[    0.138091] pci 0000:04:01.0: [1814:5362] type 00 class 0x028000
[    0.138110] pci 0000:04:01.0: reg 0x10: [mem 0xe5100000-0xe510ffff]
[    0.138246] pci 0000:00:1e.0: PCI bridge to [bus 04] (subtractive decode)
[    0.138251] pci 0000:00:1e.0:   bridge window [mem 0xe5100000-0xe51fffff]
[    0.138256] pci 0000:00:1e.0:   bridge window [io  0x0000-0x0cf7] (subtractive decode)
[    0.138257] pci 0000:00:1e.0:   bridge window [io  0x0d00-0xffff] (subtractive decode)
[    0.138259] pci 0000:00:1e.0:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[    0.138261] pci 0000:00:1e.0:   bridge window [mem 0x000c0000-0x000dffff] (subtractive decode)
[    0.138263] pci 0000:00:1e.0:   bridge window [mem 0xbff00000-0xfebfffff] (subtractive decode)
[    0.138651] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[    0.138698] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[    0.138744] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[    0.138789] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[    0.138834] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[    0.138880] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[    0.138925] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[    0.138971] ACPI: PCI Interrupt Link [LNK1] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
[    0.139050] ACPI: Enabled 1 GPEs in block 00 to 1F
[    0.139056] ACPI: \_SB_.PCI0: notify handler is installed
[    0.139077] Found 1 acpi root devices
[    0.139133] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.139133] vgaarb: loaded
[    0.139133] vgaarb: bridge control possible 0000:01:00.0
[    0.139133] SCSI subsystem initialized
[    0.139133] libata version 3.00 loaded.
[    0.139133] PCI: Using ACPI for IRQ routing
[    0.144262] PCI: pci_cache_line_size set to 64 bytes
[    0.144297] e820: reserve RAM buffer [mem 0x0009f800-0x0009ffff]
[    0.144299] e820: reserve RAM buffer [mem 0xbfee0000-0xbfffffff]
[    0.144379] NetLabel: Initializing
[    0.144380] NetLabel:  domain hash size = 128
[    0.144381] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.144390] NetLabel:  unlabeled traffic allowed by default
[    0.144415] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.144418] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.144421] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[    0.146013] Switched to clocksource hpet
[    0.151323] pnp: PnP ACPI init
[    0.151339] ACPI: bus type PNP registered
[    0.151508] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.151517] pnp 00:01: [dma 4]
[    0.151532] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.151604] pnp 00:02: Plug and Play ACPI device, IDs PNP0103 (active)
[    0.151636] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.151658] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
[    0.151680] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.151894] pnp 00:06: Plug and Play ACPI device, IDs PNP0501 (active)
[    0.152063] pnp 00:07: Plug and Play ACPI device, IDs PNP0400 (active)
[    0.152145] pnp 00:08: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.152195] system 00:09: [io  0x0400-0x04cf] could not be reserved
[    0.152198] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.152355] system 00:0a: [mem 0xc0000000-0xcfffffff] has been reserved
[    0.152358] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.152498] system 00:0b: [mem 0x000ce000-0x000cffff] has been reserved
[    0.152524] system 00:0b: [mem 0x000e0000-0x000effff] has been reserved
[    0.152526] system 00:0b: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.152556] pnp 00:0c: Plug and Play ACPI device, IDs INT0800 (active)
[    0.152560] pnp: PnP ACPI: found 13 devices
[    0.152561] ACPI: bus type PNP unregistered
[    0.158537] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000
[    0.158540] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 02] add_size 200000
[    0.158553] pci 0000:00:1f.0: BAR 13: [io  0x0400-0x047f] has bogus alignment
[    0.158556] pci 0000:00:1c.0: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
[    0.158558] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[    0.158563] pci 0000:00:1c.0: BAR 14: assigned [mem 0xe5300000-0xe54fffff]
[    0.158565] pci 0000:00:1c.0: BAR 15: assigned [mem 0xe5500000-0xe56fffff 64bit pref]
[    0.158568] pci 0000:01:00.0: BAR 6: assigned [mem 0xe3000000-0xe307ffff pref]
[    0.158571] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.158573] pci 0000:00:01.0:   bridge window [io  0xc000-0xcfff]
[    0.158576] pci 0000:00:01.0:   bridge window [mem 0xe0000000-0xe3ffffff]
[    0.158579] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.158582] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.158584] pci 0000:00:1c.0:   bridge window [io  0xb000-0xbfff]
[    0.158588] pci 0000:00:1c.0:   bridge window [mem 0xe5300000-0xe54fffff]
[    0.158591] pci 0000:00:1c.0:   bridge window [mem 0xe5500000-0xe56fffff 64bit pref]
[    0.158597] pci 0000:03:00.0: BAR 6: assigned [mem 0xe5020000-0xe503ffff pref]
[    0.158599] pci 0000:00:1c.1: PCI bridge to [bus 03]
[    0.158601] pci 0000:00:1c.1:   bridge window [io  0xd000-0xdfff]
[    0.158605] pci 0000:00:1c.1:   bridge window [mem 0xe4000000-0xe4ffffff]
[    0.158608] pci 0000:00:1c.1:   bridge window [mem 0xe5000000-0xe50fffff 64bit pref]
[    0.158613] pci 0000:00:1e.0: PCI bridge to [bus 04]
[    0.158617] pci 0000:00:1e.0:   bridge window [mem 0xe5100000-0xe51fffff]
[    0.158623] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.158625] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    0.158627] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    0.158629] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff]
[    0.158630] pci_bus 0000:00: resource 8 [mem 0xbff00000-0xfebfffff]
[    0.158632] pci_bus 0000:01: resource 0 [io  0xc000-0xcfff]
[    0.158634] pci_bus 0000:01: resource 1 [mem 0xe0000000-0xe3ffffff]
[    0.158636] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.158638] pci_bus 0000:02: resource 0 [io  0xb000-0xbfff]
[    0.158639] pci_bus 0000:02: resource 1 [mem 0xe5300000-0xe54fffff]
[    0.158641] pci_bus 0000:02: resource 2 [mem 0xe5500000-0xe56fffff 64bit pref]
[    0.158643] pci_bus 0000:03: resource 0 [io  0xd000-0xdfff]
[    0.158645] pci_bus 0000:03: resource 1 [mem 0xe4000000-0xe4ffffff]
[    0.158646] pci_bus 0000:03: resource 2 [mem 0xe5000000-0xe50fffff 64bit pref]
[    0.158648] pci_bus 0000:04: resource 1 [mem 0xe5100000-0xe51fffff]
[    0.158650] pci_bus 0000:04: resource 4 [io  0x0000-0x0cf7]
[    0.158652] pci_bus 0000:04: resource 5 [io  0x0d00-0xffff]
[    0.158654] pci_bus 0000:04: resource 6 [mem 0x000a0000-0x000bffff]
[    0.158655] pci_bus 0000:04: resource 7 [mem 0x000c0000-0x000dffff]
[    0.158657] pci_bus 0000:04: resource 8 [mem 0xbff00000-0xfebfffff]
[    0.158688] NET: Registered protocol family 2
[    0.158852] TCP established hash table entries: 32768 (order: 7, 524288 bytes)
[    0.159085] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    0.159279] TCP: Hash tables configured (established 32768 bind 32768)
[    0.159320] TCP: reno registered
[    0.159330] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.159358] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.159433] NET: Registered protocol family 1
[    0.159937] pci 0000:01:00.0: Boot video device
[    0.159944] PCI: CLS 32 bytes, default 64
[    0.159984] Trying to unpack rootfs image as initramfs...
[    0.246734] Freeing initrd memory: 7956K (ffff880037066000 - ffff88003782b000)
[    0.246742] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    0.246744] software IO TLB [mem 0xbbee0000-0xbfee0000] (64MB) mapped at [ffff8800bbee0000-ffff8800bfedffff]
[    0.247165] audit: initializing netlink socket (disabled)
[    0.247179] type=2000 audit(1397800527.246:1): initialized
[    0.267608] bounce pool size: 64 pages
[    0.267619] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.268801] zbud: loaded
[    0.268925] VFS: Disk quotas dquot_6.5.2
[    0.268960] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.269374] bio: create slab <bio-1> at 1
[    0.269502] Btrfs loaded
[    0.269507] msgmni has been set to 7900
[    0.269731] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.269755] io scheduler noop registered
[    0.269757] io scheduler deadline registered
[    0.269780] io scheduler cfq registered (default)
[    0.269929] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[    0.270020] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
[    0.270118] pcieport 0000:00:1c.1: irq 42 for MSI/MSI-X
[    0.270177] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.270189] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.270232] intel_idle: does not run on family 6 model 23
[    0.270258] GHES: HEST is not enabled!
[    0.270296] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.290780] 00:06: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[    0.291053] Linux agpgart interface v0.103
[    0.292116] brd: module loaded
[    0.292223] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[    0.292225] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[    0.292344] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.292409] mousedev: PS/2 mouse device common for all mice
[    0.292483] rtc_cmos 00:03: RTC can wake from S4
[    0.292578] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    0.292600] rtc_cmos 00:03: alarms up to one month, 242 bytes nvram, hpet irqs
[    0.292609] ledtrig-cpu: registered to indicate activity on CPUs
[    0.292693] TCP: cubic registered
[    0.292703] Key type dns_resolver registered
[    0.292704] mpls_gso: MPLS GSO support
[    0.292847] registered taskstats version 1
[    0.293296]   Magic number: 10:757:921
[    0.293365] rtc_cmos 00:03: setting system clock to 2014-04-18 05:55:28 UTC (1397800528)
[    0.293367] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.293368] EDD information not available.
[    0.293394] PM: Checking hibernation image partition UUID=db01d9fc-7995-4da3-b5e7-46c6d7448c59
[    0.311640] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    0.311659] PM: Hibernation image not present or could not be loaded.
[    0.312616] Freeing unused kernel memory: 1232K (ffffffff81cdb000 - ffffffff81e0f000)
[    0.312617] Write protecting the kernel read-only data: 12288k
[    0.316655] Freeing unused kernel memory: 1900K (ffff880001625000 - ffff880001800000)
[    0.319017] Freeing unused kernel memory: 1072K (ffff880001af4000 - ffff880001c00000)
[    0.355120] dracut: dracut-034
[    0.364765] ata_piix 0000:00:1f.2: version 2.13
[    0.364856] ata_piix 0000:00:1f.2: MAP [
[    0.364857]  P0 P2 IDE IDE ]
[    0.364888] ata_piix 0000:00:1f.2: setting latency timer to 64
[    0.365365] scsi0 : ata_piix
[    0.365434] scsi1 : ata_piix
[    0.365458] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[    0.365460] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[    0.519405] ata2.00: ATAPI: Optiarc DVD RW AD-7200A, 1.09, max UDMA/66
[    0.520184] ata1.00: HPA detected: current 976771055, native 976773168
[    0.520189] ata1.00: ATA-8: WDC WD5000AAKX-001CA0, 15.01H15, max UDMA/133
[    0.520192] ata1.00: 976771055 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    0.525198] ata2.00: configured for UDMA/66
[    0.526265] ata1.00: configured for UDMA/133
[    0.526355] scsi 0:0:0:0: Direct-Access     ATA      WDC WD5000AAKX-0 15.0 PQ: 0 ANSI: 5
[    0.526435] sd 0:0:0:0: [sda] 976771055 512-byte logical blocks: (500 GB/465 GiB)
[    0.526486] sd 0:0:0:0: [sda] Write Protect is off
[    0.526489] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    0.526547] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    0.528086] scsi 1:0:0:0: CD-ROM            Optiarc  DVD RW AD-7200A  1.09 PQ: 0 ANSI: 5
[    0.560536]  sda: sda1 sda2 sda3
[    0.560605] sda: p3 size 8192000 extends beyond EOD, enabling native capacity
[    0.560617] ata1: soft resetting link
[    0.717129] ata1.00: n_sectors mismatch 976771055 != 976773168
[    0.717132] ata1.00: new n_sectors matches native, probably late HPA unlock, n_sectors updated
[    0.723392] ata1.00: configured for UDMA/133
[    0.723397] ata1: EH complete
[    0.723434] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[    0.723693] sda: detected capacity change from 500106780160 to 500107862016
[    0.777195]  sda: sda1 sda2 sda3
[    0.777435] sd 0:0:0:0: [sda] Attached SCSI disk
[    0.789181] Uniform Multi-Platform E-IDE driver
[    0.851258] systemd-udevd[191]: starting version 208
[    0.891054] [drm] Initialized drm 1.1.0 20060810
[    0.897977] wmi: Mapper loaded
[    0.899669] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[    0.899674] ACPI: Power Button [PWRB]
[    0.899725] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[    0.899728] ACPI: Power Button [PWRF]
[    0.931854] [drm] hdmi device  not found 1 0 1
[    0.931939] nouveau  [  DEVICE][0000:01:00.0] BOOT0  : 0x096000c1
[    0.931941] nouveau  [  DEVICE][0000:01:00.0] Chipset: G96 (NV96)
[    0.931943] nouveau  [  DEVICE][0000:01:00.0] Family : NV50
[    0.932888] nouveau  [   VBIOS][0000:01:00.0] checking PRAMIN for image...
[    0.984297] nouveau  [   VBIOS][0000:01:00.0] ... appears to be valid
[    0.984298] nouveau  [   VBIOS][0000:01:00.0] using image from PRAMIN
[    0.984396] nouveau  [   VBIOS][0000:01:00.0] BIT signature found
[    0.984398] nouveau  [   VBIOS][0000:01:00.0] version 62.94.4b.00.00
[    1.004580] nouveau  [     PFB][0000:01:00.0] RAM type: DDR2
[    1.004582] nouveau  [     PFB][0000:01:00.0] RAM size: 1024 MiB
[    1.004584] nouveau  [     PFB][0000:01:00.0]    ZCOMP: 2048 tags
[    1.027062] nouveau  [  PTHERM][0000:01:00.0] FAN control: PWM
[    1.027070] nouveau  [  PTHERM][0000:01:00.0] fan management: disabled
[    1.027073] nouveau  [  PTHERM][0000:01:00.0] internal sensor: yes
[    1.027188] [TTM] Zone  kernel: Available graphics memory: 2024612 kiB
[    1.027190] [TTM] Initializing pool allocator
[    1.027194] [TTM] Initializing DMA pool allocator
[    1.027201] nouveau  [     DRM] VRAM: 1024 MiB
[    1.027202] nouveau  [     DRM] GART: 1048576 MiB
[    1.027205] nouveau  [     DRM] TMDS table version 2.0
[    1.027206] nouveau  [     DRM] DCB version 4.0
[    1.027208] nouveau  [     DRM] DCB outp 00: 02000300 00000028
[    1.027210] nouveau  [     DRM] DCB outp 01: 01000302 00020030
[    1.027212] nouveau  [     DRM] DCB outp 02: 04011310 00000028
[    1.027213] nouveau  [     DRM] DCB outp 03: 02021342 00020030
[    1.027215] nouveau  [     DRM] DCB outp 04: 010223f1 00c0c080
[    1.027216] nouveau  [     DRM] DCB conn 00: 00001030
[    1.027218] nouveau  [     DRM] DCB conn 01: 00002130
[    1.027220] nouveau  [     DRM] DCB conn 02: 00000200
[    1.035841] nouveau W[     DRM] failed to create encoder 0/1/0: -19
[    1.035843] nouveau W[     DRM] VGA-1 has no encoders, removing
[    1.035862] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[    1.035863] [drm] No driver support for vblank timestamp query.
[    1.035955] nouveau  [     DRM] 1 available performance level(s)
[    1.035958] nouveau  [     DRM] 3: core 550MHz shader 1375MHz memory 333MHz fanspeed 100%
[    1.035960] nouveau  [     DRM] c: core 400MHz shader 800MHz memory 300MHz fanspeed 40%
[    1.247018] tsc: Refined TSC clocksource calibration: 2933.297 MHz
[    1.295149] nouveau  [     DRM] MM: using CRYPT for buffer copies
[    1.338998] nouveau  [     DRM] allocated 1440x900 fb: 0x70000, bo ffff88003729ac00
[    1.339047] fbcon: nouveaufb (fb0) is primary device
[    1.417322] Console: switching to colour frame buffer device 180x56
[    1.418927] nouveau 0000:01:00.0: fb0: nouveaufb frame buffer device
[    1.418928] nouveau 0000:01:00.0: registered panic notifier
[    1.418932] [drm] Initialized nouveau 1.1.1 20120801 for 0000:01:00.0 on minor 0
[    1.420992] dracut: Starting plymouth daemon
[    2.247079] Switched to clocksource tsc
[    2.624893] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[    2.624897] cdrom: Uniform CD-ROM driver Revision: 3.20
[    2.624991] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    2.643104] ACPI: bus type USB registered
[    2.643131] usbcore: registered new interface driver usbfs
[    2.643139] usbcore: registered new interface driver hub
[    2.646043] usbcore: registered new device driver usb
[    2.649277] uhci_hcd: USB Universal Host Controller Interface driver
[    2.649400] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    2.649403] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    2.649409] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[    2.649447] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000e000
[    2.651259] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[    2.651262] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.651264] usb usb1: Product: UHCI Host Controller
[    2.651266] usb usb1: Manufacturer: Linux 3.12.13-desktop-2.mga4 uhci_hcd
[    2.651268] usb usb1: SerialNumber: 0000:00:1d.0
[    2.651370] hub 1-0:1.0: USB hub found
[    2.651377] hub 1-0:1.0: 2 ports detected
[    2.651540] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    2.651543] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    2.651548] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[    2.651583] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e100
[    2.651623] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    2.651625] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.651627] usb usb2: Product: UHCI Host Controller
[    2.651628] usb usb2: Manufacturer: Linux 3.12.13-desktop-2.mga4 uhci_hcd
[    2.651630] usb usb2: SerialNumber: 0000:00:1d.1
[    2.651698] hub 2-0:1.0: USB hub found
[    2.651704] hub 2-0:1.0: 2 ports detected
[    2.651820] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    2.651823] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    2.651827] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[    2.651853] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e200
[    2.652030] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    2.652033] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.652035] usb usb3: Product: UHCI Host Controller
[    2.652036] usb usb3: Manufacturer: Linux 3.12.13-desktop-2.mga4 uhci_hcd
[    2.652038] usb usb3: SerialNumber: 0000:00:1d.2
[    2.652115] hub 3-0:1.0: USB hub found
[    2.652122] hub 3-0:1.0: 2 ports detected
[    2.654200] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[    2.654204] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    2.654210] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[    2.654234] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000e300
[    2.654277] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    2.654279] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.654281] usb usb4: Product: UHCI Host Controller
[    2.654282] usb usb4: Manufacturer: Linux 3.12.13-desktop-2.mga4 uhci_hcd
[    2.654284] usb usb4: SerialNumber: 0000:00:1d.3
[    2.654363] hub 4-0:1.0: USB hub found
[    2.654370] hub 4-0:1.0: 2 ports detected
[    2.664872] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.664875] Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
[    2.665344] ehci-pci: EHCI PCI platform driver
[    2.665465] ehci-pci 0000:00:1d.7: setting latency timer to 64
[    2.666597] ehci-pci 0000:00:1d.7: EHCI Host Controller
[    2.666605] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 5
[    2.670530] ehci-pci 0000:00:1d.7: cache line size of 32 is not supported
[    2.670739] ehci-pci 0000:00:1d.7: irq 23, io mem 0xe5204000
[    2.676013] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    2.676077] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[    2.676079] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.676081] usb usb5: Product: EHCI Host Controller
[    2.676082] usb usb5: Manufacturer: Linux 3.12.13-desktop-2.mga4 ehci_hcd
[    2.676084] usb usb5: SerialNumber: 0000:00:1d.7
[    2.676233] hub 5-0:1.0: USB hub found
[    2.676257] hub 5-0:1.0: 8 ports detected
[    2.697092] hub 1-0:1.0: USB hub found
[    2.697107] hub 1-0:1.0: 2 ports detected
[    2.718127] hub 2-0:1.0: USB hub found
[    2.718138] hub 2-0:1.0: 2 ports detected
[    2.739075] hub 3-0:1.0: USB hub found
[    2.739095] hub 3-0:1.0: 2 ports detected
[    2.760059] hub 4-0:1.0: USB hub found
[    2.760070] hub 4-0:1.0: 2 ports detected
[    2.978028] usb 5-2: new high-speed USB device number 2 using ehci-pci
[    3.111532] usb 5-2: New USB device found, idVendor=148f, idProduct=5370
[    3.111537] usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    3.111540] usb 5-2: Product: 802.11 n WLAN
[    3.111543] usb 5-2: Manufacturer: TPlink
[    3.111546] usb 5-2: SerialNumber: 1.0
[    3.171063] PM: Marking nosave pages: [mem 0x0009f000-0x000fffff]
[    3.171068] PM: Marking nosave pages: [mem 0xbfee0000-0xffffffff]
[    3.171656] PM: Basic memory bitmaps created
[    3.186278] PM: Basic memory bitmaps freed
[    3.188775] PM: Starting manual resume from disk
[    3.188779] PM: Hibernation image partition 8:3 present
[    3.188780] PM: Looking for hibernation image.
[    3.189836] PM: Image not found (code -22)
[    3.189838] PM: Hibernation image not present or could not be loaded.
[    3.230150] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[    3.266061] usb 5-5: new high-speed USB device number 4 using ehci-pci
[    3.301063] dracut: Checking ext4: /dev/disk/by-uuid/50be33c3-f160-43a4-82af-77bc8fa83ea2
[    3.301212] dracut: issuing e2fsck -a  /dev/disk/by-uuid/50be33c3-f160-43a4-82af-77bc8fa83ea2
[    3.334980] dracut: /dev/disk/by-uuid/50be33c3-f160-43a4-82af-77bc8fa83ea2: clean, 64458/1921360 files, 740470/7680000 blocks
[    3.336211] dracut: Mounting /dev/disk/by-uuid/50be33c3-f160-43a4-82af-77bc8fa83ea2 with -o acl,relatime,ro
[    3.403033] usb 5-5: New USB device found, idVendor=0ac8, idProduct=3420
[    3.403039] usb 5-5: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    3.403042] usb 5-5: Product: A4TECH USB2.0 PC Camera
[    3.403045] usb 5-5: Manufacturer: A4TECH Corp.
[    3.413529] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: acl
[    3.466999] dracut: Mounted root filesystem /dev/sda1
[    3.616162] dracut: Switching root
[    3.617797] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist.
[    3.661034] usb 4-2: new low-speed USB device number 2 using uhci_hcd
[    3.928989] systemd[1]: systemd 208 running in system mode. (+PAM +LIBWRAP +AUDIT -SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ)
[    4.025033] usb 4-2: New USB device found, idVendor=093a, idProduct=2510
[    4.025038] usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    4.025041] usb 4-2: Product: USB Optical Mouse
[    4.025044] usb 4-2: Manufacturer: PixArt
[    4.067602] systemd[1]: Inserted module 'autofs4'
[    4.116753] NET: Registered protocol family 10
[    4.116972] systemd[1]: Inserted module 'ipv6'
[    4.122081] systemd[1]: Set hostname to <localhost>.
[    4.493041] usb 5-3: new high-speed USB device number 7 using ehci-pci
[    4.588765] systemd[1]: Starting Replay Read-Ahead Data...
[    5.512033] usb 5-3: new high-speed USB device number 12 using ehci-pci
[    5.535318] ACPI: Requesting acpi_cpufreq
[    5.538746] systemd[1]: Started Load legacy module configuration.
[    5.618023] systemd[1]: Started File System Check on Root Device.
[    5.618128] systemd[1]: Starting Remount Root and Kernel File Systems...
[    5.826767] systemd-udevd[494]: starting version 208
[    5.860503] EXT4-fs (sda1): re-mounted. Opts: acl
[    6.094196] IT8718 SuperIO detected.
[    6.094445] parport_pc 00:07: reported by Plug and Play ACPI
[    6.094483] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[    6.095353] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    6.105898] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    6.105909] r8169 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
[    6.111521] r8169 0000:03:00.0: irq 43 for MSI/MSI-X
[    6.112131] r8169 0000:03:00.0 eth0: RTL8102e at 0xffffc9001079a000, 00:24:1d:90:ad:c4, XID 14a00000 IRQ 43
[    6.113278] intel_rng: FWH not detected
[    6.116152] i801_smbus 0000:00:1f.3: SMBus using PCI Interrupt
[    6.120671] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \GP2C 1 (20130725/utaddress-251)
[    6.120678] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    6.120695] lpc_ich: Resource conflict(s) found affecting gpio_ich
[    6.123347] leds_ss4200: no LED devices found
[    6.125269] microcode: CPU0 sig=0x1067a, pf=0x1, revision=0xa07
[    6.141820] microcode: CPU1 sig=0x1067a, pf=0x1, revision=0xa07
[    6.141879] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    6.166248] cfg80211: Calling CRDA to update world regulatory domain
[    6.167489] snd_hda_intel 0000:00:1b.0: irq 44 for MSI/MSI-X
[    6.169026] usb 5-3: new high-speed USB device number 15 using ehci-pci
[    6.176111] systemd-udevd[511]: renamed network interface eth0 to enp3s0
[    6.177694] ppdev: user-space parallel port driver
[    6.179112] iTCO_vendor_support: vendor-support=0
[    6.179243] gpio_ich: GPIO from 206 to 255 on gpio_ich
[    6.179635] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
[    6.179659] iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0460)
[    6.180678] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=1)
[    6.191169] SKU: Nid=0x0 sku_cfg=0x0000c603
[    6.191173] SKU: port_connectivity=0x0
[    6.191174] SKU: enable_pcbeep=0x1
[    6.191176] SKU: check_sum=0x00000000
[    6.191176] SKU: customization=0x00000000
[    6.191177] SKU: external_amp=0x0
[    6.191179] SKU: platform_type=0x0
[    6.191179] SKU: swap=0x1
[    6.191180] SKU: override=0x1
[    6.191498] autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:line
[    6.191499]    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[    6.191500]    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[    6.191501]    mono: mono_out=0x0
[    6.191502]    dig-out=0x1e/0x0
[    6.191503]    inputs:
[    6.191505]      Rear Mic=0x18
[    6.191506]      Front Mic=0x19
[    6.191507]      Line=0x1a
[    6.191508]      CD=0x1c
[    6.191510] realtek: Enabling init ASM_ID=0xc603 CODEC_ID=10ec0883
[    6.195234] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input3
[    6.202629] pci 0000:00:1e.0: setting latency timer to 64
[    6.202751] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5392, rev 0223 detected
[    6.206169] ieee80211 phy0: rt2800_init_eeprom: Error - Invalid RF chipset 0x5362 detected
[    6.206171] ieee80211 phy0: rt2x00lib_probe_dev: Error - Failed to allocate device
[    6.206451] input: HDA Intel Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[    6.206514] input: HDA Intel Line Out as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[    6.206554] input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6
[    6.206594] input: HDA Intel Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input5
[    6.206634] input: HDA Intel Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input4
[    6.247250] cfg80211: World regulatory domain updated:
[    6.247254] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    6.247255] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[    6.247257] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[    6.247258] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[    6.247260] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[    6.247261] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[    6.247262] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[    6.347352] hidraw: raw HID events driver (C) Jiri Kosina
[    6.363340] usbcore: registered new interface driver usbhid
[    6.363343] usbhid: USB HID core driver
[    6.364286] input: PixArt USB Optical Mouse as /devices/pci0000:00/0000:00:1d.3/usb4/4-2/4-2:1.0/input/input9
[    6.364364] hid-generic 0003:093A:2510.0001: input,hidraw0: USB HID v1.11 Mouse [PixArt USB Optical Mouse] on usb-0000:00:1d.3-2/input0
[    6.464017] usb 5-3: new high-speed USB device number 16 using ehci-pci
[    7.483043] usb 5-3: new high-speed USB device number 21 using ehci-pci
[    7.778024] usb 5-3: new high-speed USB device number 22 using ehci-pci
[    8.176414] Adding 4095996k swap on /dev/sda3.  Priority:-1 extents:1 across:4095996k FS
[    8.797027] usb 5-3: new high-speed USB device number 27 using ehci-pci
[    9.092036] usb 5-3: new high-speed USB device number 28 using ehci-pci
[    9.192528] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: acl
[    9.236385] systemd-journald[444]: Received request to flush runtime journal from PID 1
[    9.568031] usb 5-3: new high-speed USB device number 30 using ehci-pci
[    9.663612] r8169 0000:03:00.0 enp3s0: link down
[    9.664444] IPv6: ADDRCONF(NETDEV_UP): enp3s0: link is not ready
[    9.863060] usb 5-3: new high-speed USB device number 31 using ehci-pci
[    9.971028] systemd[1]: Received SIGRTMIN+21 from PID 240 (n/a).
[   10.339027] usb 5-3: new high-speed USB device number 33 using ehci-pci
[   10.636028] usb 5-3: new high-speed USB device number 34 using ehci-pci
[   10.931027] usb 5-3: new high-speed USB device number 35 using ehci-pci
[   11.226030] usb 5-3: new high-speed USB device number 36 using ehci-pci
[   12.066174] usb 5-3: new high-speed USB device number 40 using ehci-pci
[   13.270029] usb 5-3: new high-speed USB device number 46 using ehci-pci
[   13.542035] usb 5-2: reset high-speed USB device number 2 using ehci-pci
[   13.668660] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 5390, rev 0502 detected
[   13.696784] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 5370 detected
[   13.699639] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[   13.699871] usbcore: registered new interface driver rt2800usb
[   13.700030] Loading kernel module for a network device with CAP_SYS_MODULE (deprecated).  Use CAP_NET_ADMIN and alias netdev-wlp0s29f7u2 instead.
[   13.943027] usb 5-3: new high-speed USB device number 48 using ehci-pci
[   14.604030] usb 5-3: new high-speed USB device number 51 using ehci-pci
[   17.441024] usb 2-1: new full-speed USB device number 2 using uhci_hcd
[   17.570035] usb 2-1: not running at top speed; connect to a high speed hub
[   17.610035] usb 2-1: New USB device found, idVendor=0aec, idProduct=3260
[   17.610042] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   17.610045] usb 2-1: Product: USB Storage Device
[   17.610048] usb 2-1: Manufacturer: GENERIC
[   17.610051] usb 2-1: SerialNumber: 200510251942096LD
[   17.646934] media: Linux media interface: v0.10
[   17.651287] systemd-udevd[504]: renamed network interface wlan0 to wlp0s29f7u2
[   17.656141] Linux video capture interface: v2.00
[   17.712082] cfg80211: Calling CRDA for country: GR
[   17.717206] usb-storage 2-1:1.0: USB Mass Storage device detected
[   17.718077] scsi2 : usb-storage 2-1:1.0
[   17.718477] usbcore: registered new interface driver usb-storage
[   17.722941] cfg80211: Regulatory domain changed to country: GR
[   17.722945] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   17.722949] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   17.722951] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[   17.722954] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[   17.722957] cfg80211:   (5490000 KHz - 5710000 KHz @ 80000 KHz), (N/A, 2700 mBm)
[   17.722959] cfg80211:   (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
[   18.109186] ieee80211 phy1: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'
[   18.152544] ieee80211 phy1: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.29
[   18.358831] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u2: link is not ready
[   18.615832] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u2: link is not ready
[   18.654589] NET: Registered protocol family 17
[   18.726055] scsi 2:0:0:0: Direct-Access     GENERIC  USB Storage-SMC  I19B PQ: 0 ANSI: 0 CCS
[   18.738050] scsi 2:0:0:1: Direct-Access     GENERIC  USB Storage-CFC  I19B PQ: 0 ANSI: 0 CCS
[   18.754077] scsi 2:0:0:2: Direct-Access     GENERIC  USB Storage-SDC  I19B PQ: 0 ANSI: 0 CCS
[   18.775106] scsi 2:0:0:3: Direct-Access     GENERIC  USB Storage-MSC  I19B PQ: 0 ANSI: 0 CCS
[   18.779366] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   18.797928] ip_tables: (C) 2000-2006 Netfilter Core Team
[   18.844592] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[   18.867052] sd 2:0:0:1: [sdc] Attached SCSI removable disk
[   18.884055] sd 2:0:0:2: [sdd] Attached SCSI removable disk
[   18.895041] sd 2:0:0:3: [sde] Attached SCSI removable disk
[   19.257377] Netfilter messages via NETLINK v0.30.
[   19.270120] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[   19.377253] xt_time: kernel timezone is +0300
[   19.416121] ctnetlink v0.93: registering with nfnetlink.
[   19.479440] ip_set: protocol 6
[   19.589302] wlp0s29f7u2: authenticate with 00:13:33:84:db:37
[   19.596560] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
[   19.625800] wlp0s29f7u2: send auth to 00:13:33:84:db:37 (try 1/3)
[   19.628520] wlp0s29f7u2: authenticated
[   19.628554] rt2800usb 5-2:1.0 wlp0s29f7u2: disabling HT as WMM/QoS is not supported by the AP
[   19.628556] rt2800usb 5-2:1.0 wlp0s29f7u2: disabling VHT as WMM/QoS is not supported by the AP
[   19.629022] wlp0s29f7u2: associate with 00:13:33:84:db:37 (try 1/3)
[   19.630928] wlp0s29f7u2: RX AssocResp from 00:13:33:84:db:37 (capab=0x411 status=0 aid=5)
[   19.639170] wlp0s29f7u2: associated
[   19.639200] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u2: link becomes ready
[   19.921730] xt_addrtype: ipv6 does not support BROADCAST matching
[   20.258441] xt_CT: No such helper "irc"
[   20.270818] xt_CT: No such helper "irc-0"
[   20.281000] xt_CT: No such helper "netbios-ns"
[   20.298499] xt_CT: No such helper "snmp"
[   20.310992] xt_CT: No such helper "pptp"
[   20.414859] Bridge firewalling registered
[   20.647079] u32 classifier
[   20.647083]     Actions configured
[   22.026873] ipt_ULOG: ULOG is deprecated and it will be removed soon, use NFLOG instead
[   22.377513] netfilter PSD loaded - (c) astaro AG
[   22.378926] IFWLOG: register target
[   67.675613] usbcore: registered new interface driver snd-usb-audio
[   67.675616] uvcvideo: Found UVC 1.00 device A4TECH USB2.0 PC Camera (0ac8:3420)
[   67.679203] input: A4TECH USB2.0 PC Camera as /devices/pci0000:00/0000:00:1d.7/usb5/5-5/5-5:1.0/input/input10
[   67.679376] usbcore: registered new interface driver uvcvideo
[   67.679379] USB Video Class driver (1.1.1)
[  214.822986] cfg80211: Calling CRDA to update world regulatory domain
[  214.826050] cfg80211: World regulatory domain updated:
[  214.826055] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[  214.826058] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  214.826061] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  214.826064] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[  214.826066] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[  214.826069] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[  214.826072] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[  214.826087] cfg80211: Calling CRDA for country: GR
[  214.828529] cfg80211: Regulatory domain changed to country: GR
[  214.828533] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[  214.828537] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  214.828539] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[  214.828542] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[  214.828545] cfg80211:   (5490000 KHz - 5710000 KHz @ 80000 KHz), (N/A, 2700 mBm)
[  214.828547] cfg80211:   (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
[  215.861301] wlp0s29f7u2: authenticate with 00:13:33:84:db:37
[  215.878967] wlp0s29f7u2: send auth to 00:13:33:84:db:37 (try 1/3)
[  215.916101] wlp0s29f7u2: send auth to 00:13:33:84:db:37 (try 2/3)
[  215.952223] wlp0s29f7u2: send auth to 00:13:33:84:db:37 (try 3/3)
[  215.982722] wlp0s29f7u2: authentication with 00:13:33:84:db:37 timed out
[  221.845801] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u2: link is not ready
[  222.865842] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 12 in queue 0
[  222.865863] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 12 in queue 0
[  222.865867] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 12 in queue 0
[  234.680311] wlp0s29f7u2: authenticate with 00:13:33:84:db:37
[  234.697974] wlp0s29f7u2: send auth to 00:13:33:84:db:37 (try 1/3)
[  234.699354] wlp0s29f7u2: authenticated
[  234.699371] rt2800usb 5-2:1.0 wlp0s29f7u2: disabling HT as WMM/QoS is not supported by the AP
[  234.699375] rt2800usb 5-2:1.0 wlp0s29f7u2: disabling VHT as WMM/QoS is not supported by the AP
[  234.700012] wlp0s29f7u2: associate with 00:13:33:84:db:37 (try 1/3)
[  234.701852] wlp0s29f7u2: RX AssocResp from 00:13:33:84:db:37 (capab=0x411 status=0 aid=5)
[  234.708597] wlp0s29f7u2: associated
[  234.708623] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u2: link becomes ready
[  542.530059] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 8 in queue 2
[  542.530082] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 8 in queue 2
[  542.530087] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 8 in queue 2
[  542.542430] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 9 in queue 2
[  542.542445] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 9 in queue 2
[  542.542450] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 9 in queue 2
[  542.553684] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 10 in queue 2
[  542.553699] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 10 in queue 2
[  542.610698] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 15 in queue 2
[  542.610704] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 15 in queue 2
[  542.621930] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 0 in queue 2
[  542.621942] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 0 in queue 2
[  542.621946] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 0 in queue 2
[  542.633182] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 1 in queue 2
[  542.633195] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 1 in queue 2
[  542.633201] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 1 in queue 2
[  542.641055] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 2 in queue 2
[  542.641075] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 2 in queue 2
[  542.641078] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 2 in queue 2
[  542.652306] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 3 in queue 2
[  542.652318] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 3 in queue 2
[  542.652322] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 3 in queue 2
[  542.679433] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[  542.737686] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[  542.737803] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[  542.737929] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[  542.738472] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[  542.738477] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[  542.738479] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[  542.738557] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[  542.738682] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[  542.738802] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[  542.739631] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[  542.739635] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[  611.882967] cfg80211: Calling CRDA to update world regulatory domain
[  611.886053] cfg80211: World regulatory domain updated:
[  611.886058] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[  611.886061] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  611.886064] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  611.886067] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[  611.886070] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[  611.886072] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[  611.886075] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[  611.886090] cfg80211: Calling CRDA for country: GR
[  611.888493] cfg80211: Regulatory domain changed to country: GR
[  611.888497] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[  611.888500] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  611.888503] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[  611.888506] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[  611.888509] cfg80211:   (5490000 KHz - 5710000 KHz @ 80000 KHz), (N/A, 2700 mBm)
[  611.888511] cfg80211:   (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
[  612.922304] wlp0s29f7u2: authenticate with 00:13:33:84:db:37
[  612.939956] wlp0s29f7u2: send auth to 00:13:33:84:db:37 (try 1/3)
[  612.965836] wlp0s29f7u2: send auth to 00:13:33:84:db:37 (try 2/3)
[  613.009839] wlp0s29f7u2: send auth to 00:13:33:84:db:37 (try 3/3)
[  613.054958] wlp0s29f7u2: authentication with 00:13:33:84:db:37 timed out
[  619.096784] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u2: link is not ready
[  620.039323] wlp0s29f7u2: authenticate with 00:13:33:84:db:37
[  620.056956] wlp0s29f7u2: send auth to 00:13:33:84:db:37 (try 1/3)
[  620.058342] wlp0s29f7u2: authenticated
[  620.058361] rt2800usb 5-2:1.0 wlp0s29f7u2: disabling HT as WMM/QoS is not supported by the AP
[  620.058365] rt2800usb 5-2:1.0 wlp0s29f7u2: disabling VHT as WMM/QoS is not supported by the AP
[  620.059013] wlp0s29f7u2: associate with 00:13:33:84:db:37 (try 1/3)
[  620.060959] wlp0s29f7u2: RX AssocResp from 00:13:33:84:db:37 (capab=0x411 status=0 aid=5)
[  620.067706] wlp0s29f7u2: associated
[  620.067718] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u2: link becomes ready
[  620.170201] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 0 in queue 2
[  620.170214] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 0 in queue 2
[  620.170219] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 0 in queue 2
[  660.172965] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 10 in queue 2
[  681.081100] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 5 in queue 2
[  681.081104] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 5 in queue 2
[  681.120351] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[  681.120471] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[  681.120595] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[[  681.184968] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[  681.185094] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[  682.908471] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 9 in queue 2
[  682.908491] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 9 in queue 2
[  682.908495] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 9 in queue 2
[  682.910717] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 10 in queue 2
[  682.944484] ieee80211 phy1: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 7 in queue 2
[  682.978600] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[  682.978717] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[  682.978845] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[  682.994970] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[  682.995097] ieee80211 phy1: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
[  740.003051] usb 5-2: USB disconnect, device number 2
[  741.114013] ieee80211 phy1: rt2800_wait_wpdma_ready: Error - WPDMA TX/RX busy [0xffffffff]
[  741.118029] wlp0s29f7u2: deauthenticating from 00:13:33:84:db:37 by local choice (reason=3)
[  741.134676] cfg80211: Calling CRDA to update world regulatory domain
[  741.137846] cfg80211: World regulatory domain updated:
[  741.137851] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[  741.137854] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  741.137857] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  741.137860] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[  741.137862] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[  741.137865] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[  741.137868] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[  741.137884] cfg80211: Calling CRDA for country: GR
[  741.139396] Loading kernel module for a network device with CAP_SYS_MODULE (deprecated).  Use CAP_NET_ADMIN and alias netdev-wlp0s29f7u2 instead.
[  741.143965] Loading kernel module for a network device with CAP_SYS_MODULE (deprecated).  Use CAP_NET_ADMIN and alias netdev-wlp0s29f7u2 instead.
[  741.144645] cfg80211: Regulatory domain changed to country: GR
[  741.144649] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[  741.144652] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  741.144655] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[  741.144658] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[  741.144661] cfg80211:   (5490000 KHz - 5710000 KHz @ 80000 KHz), (N/A, 2700 mBm)
[  741.144663] cfg80211:   (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
[  741.152345] Loading kernel module for a network device with CAP_SYS_MODULE (deprecated).  Use CAP_NET_ADMIN and alias netdev-wlp0s29f7u2 instead.
[  741.274739] Loading kernel module for a network device with CAP_SYS_MODULE (deprecated).  Use CAP_NET_ADMIN and alias netdev-wlp0s29f7u2 instead.
[  741.277215] Loading kernel module for a network device with CAP_SYS_MODULE (deprecated).  Use CAP_NET_ADMIN and alias netdev-wlp0s29f7u2 instead.
[  760.580542] Loading kernel module for a network device with CAP_SYS_MODULE (deprecated).  Use CAP_NET_ADMIN and alias netdev-wlp0s29f7u2 instead.
[  760.583071] Loading kernel module for a network device with CAP_SYS_MODULE (deprecated).  Use CAP_NET_ADMIN and alias netdev-wlp0s29f7u2 instead.
[  797.174026] usb 5-2: new high-speed USB device number 65 using ehci-pci
[  797.307518] usb 5-2: New USB device found, idVendor=148f, idProduct=5370
[  797.307524] usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  797.307527] usb 5-2: Product: 802.11 n WLAN
[  797.307530] usb 5-2: Manufacturer: TPlink
[  797.307533] usb 5-2: SerialNumber: 1.0
[  797.412031] usb 5-2: reset high-speed USB device number 65 using ehci-pci
[  797.538646] ieee80211 phy2: rt2x00_set_rt: Info - RT chipset 5390, rev 0502 detected
[  797.566771] ieee80211 phy2: rt2x00_set_rf: Info - RF chipset 5370 detected
[  797.567153] ieee80211 phy2: Selected rate control algorithm 'minstrel_ht'
[  797.581173] systemd-udevd[4248]: renamed network interface wlan0 to wlp0s29f7u2
[  797.662030] ieee80211 phy2: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'
[  797.662076] ieee80211 phy2: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.29
[  797.870448] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u2: link is not ready
[  798.126809] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u2: link is not ready
[  799.083312] wlp0s29f7u2: authenticate with 00:13:33:84:db:37
[  799.113775] wlp0s29f7u2: send auth to 00:13:33:84:db:37 (try 1/3)
[  799.115156] wlp0s29f7u2: authenticated
[  799.115172] rt2800usb 5-2:1.0 wlp0s29f7u2: disabling HT as WMM/QoS is not supported by the AP
[  799.115176] rt2800usb 5-2:1.0 wlp0s29f7u2: disabling VHT as WMM/QoS is not supported by the AP
[  799.116016] wlp0s29f7u2: associate with 00:13:33:84:db:37 (try 1/3)
[  799.117902] wlp0s29f7u2: RX AssocResp from 00:13:33:84:db:37 (capab=0x411 status=0 aid=5)
[  799.124648] wlp0s29f7u2: associated
[  799.124672] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u2: link becomes ready
Intel Core i5-6300U CPU @ 2.40GHz ‖ RAM 7860 MiB ‖ HP 8079 - HP HP EliteBook 840 G3
Intel Skylake GT2 [HD Graphics 520] [8086:1916] {i915}
wlp2s0: Intel Wireless 8260 [8086:24f3] (rev 3a) ⋮ enp0s31f6: Intel Ethernet Connection I219-LM [8086:156f] (rev 21)

Άβαταρ μέλους
airmaik
Δημοσιεύσεις: 637
Εγγραφή: Τρί Ιουν 07, 2011 16:44 pm

Re: προβλημα με wi-fi

Δημοσίευση από airmaik » Παρ Απρ 18, 2014 08:18 am

Κώδικας: Επιλογή όλων

lpcidrake

Κώδικας: Επιλογή όλων

command not found
Intel Core i5-6300U CPU @ 2.40GHz ‖ RAM 7860 MiB ‖ HP 8079 - HP HP EliteBook 840 G3
Intel Skylake GT2 [HD Graphics 520] [8086:1916] {i915}
wlp2s0: Intel Wireless 8260 [8086:24f3] (rev 3a) ⋮ enp0s31f6: Intel Ethernet Connection I219-LM [8086:156f] (rev 21)

Άβαταρ μέλους
dglent
Δημοσιεύσεις: 934
Εγγραφή: Τετ Ιουν 01, 2011 05:42 am
Τοποθεσία: Γαλλία

Re: προβλημα με wi-fi

Δημοσίευση από dglent » Παρ Απρ 18, 2014 08:20 am

λάθος μου:
lspcidrake

Άβαταρ μέλους
airmaik
Δημοσιεύσεις: 637
Εγγραφή: Τρί Ιουν 07, 2011 16:44 pm

Re: προβλημα με wi-fi

Δημοσίευση από airmaik » Παρ Απρ 18, 2014 08:22 am

Κώδικας: Επιλογή όλων

rt2800pci       : Ralink corp.|Device 5362 [NETWORK_OTHER]
r8169           : Realtek Semiconductor Co., Ltd.|RTL8101E/RTL8102E PCI Express Fast Ethernet controller [NETWORK_ETHERNET] (rev: 02)
Card:NVIDIA GeForce 8100 to GeForce 360: NVIDIA Corporation|G96 [GeForce 9500 GT] [DISPLAY_VGA] (rev: a1)
i2c_i801        : Intel Corporation|NM10/ICH7 Family SMBus Controller [SERIAL_SMBUS] (rev: 01)
ata_piix        : Intel Corporation|NM10/ICH7 Family SATA Controller [IDE mode] [STORAGE_IDE] (rev: 01)
intel_rng       : Intel Corporation|82801GB/GR (ICH7 Family) LPC Interface Bridge [BRIDGE_ISA] (rev: 01)
unknown         : Intel Corporation|82801 PCI Bridge [BRIDGE_PCI] (rev: e1)
ehci_pci        : Intel Corporation|NM10/ICH7 Family USB2 EHCI Controller [SERIAL_USB] (rev: 01)
uhci_hcd        : Intel Corporation|NM10/ICH7 Family USB UHCI Controller #4 [SERIAL_USB] (rev: 01)
uhci_hcd        : Intel Corporation|NM10/ICH7 Family USB UHCI Controller #3 [SERIAL_USB] (rev: 01)
uhci_hcd        : Intel Corporation|NM10/ICH7 Family USB UHCI Controller #2 [SERIAL_USB] (rev: 01)
uhci_hcd        : Intel Corporation|NM10/ICH7 Family USB UHCI Controller #1 [SERIAL_USB] (rev: 01)
shpchp          : Intel Corporation|NM10/ICH7 Family PCI Express Port 2 [BRIDGE_PCI] (rev: 01)
shpchp          : Intel Corporation|NM10/ICH7 Family PCI Express Port 1 [BRIDGE_PCI] (rev: 01)
snd_hda_intel   : Intel Corporation|NM10/ICH7 Family High Definition Audio Controller [MULTIMEDIA_AUDIO_DEV] (rev: 01)
shpchp          : Intel Corporation|82G33/G31/P35/P31 Express PCI Express Root Port [BRIDGE_PCI] (rev: 10)
unknown         : Intel Corporation|82G33/G31/P35/P31 Express DRAM Controller [BRIDGE_HOST] (rev: 10)
hub             : Linux 3.12.13-desktop-2.mga4 ehci_hcd|EHCI Host Controller [Hub|Unused|Full speed (or root) hub]
rt2800usb       : TPlink|802.11 n WLAN
uvcvideo        : A4TECH Corp.|A4TECH USB2.0 PC Camera [Video|Video Control]
hub             : Linux 3.12.13-desktop-2.mga4 uhci_hcd|UHCI Host Controller [Hub|Unused|Full speed (or root) hub]
usbhid          : PixArt|USB Optical Mouse [Human Interface Device|Boot Interface Subclass|Mouse]
hub             : Linux 3.12.13-desktop-2.mga4 uhci_hcd|UHCI Host Controller [Hub|Unused|Full speed (or root) hub]
hub             : Linux 3.12.13-desktop-2.mga4 uhci_hcd|UHCI Host Controller [Hub|Unused|Full speed (or root) hub]
usb_storage     : GENERIC|USB Storage Device [Mass Storage|SCSI|Bulk-Only]
hub             : Linux 3.12.13-desktop-2.mga4 uhci_hcd|UHCI Host Controller [Hub|Unused|Full speed (or root) hub]
hid_generic     : PixArt USB Optical Mouse
Intel Core i5-6300U CPU @ 2.40GHz ‖ RAM 7860 MiB ‖ HP 8079 - HP HP EliteBook 840 G3
Intel Skylake GT2 [HD Graphics 520] [8086:1916] {i915}
wlp2s0: Intel Wireless 8260 [8086:24f3] (rev 3a) ⋮ enp0s31f6: Intel Ethernet Connection I219-LM [8086:156f] (rev 21)

Άβαταρ μέλους
dglent
Δημοσιεύσεις: 934
Εγγραφή: Τετ Ιουν 01, 2011 05:42 am
Τοποθεσία: Γαλλία

Re: προβλημα με wi-fi

Δημοσίευση από dglent » Παρ Απρ 18, 2014 08:37 am

Δες μήπως χρειάζεται αυτό:
https://forums.mageia.org/en/viewtopic.php?f=8&t=5845

Άβαταρ μέλους
airmaik
Δημοσιεύσεις: 637
Εγγραφή: Τρί Ιουν 07, 2011 16:44 pm

Re: προβλημα με wi-fi

Δημοσίευση από airmaik » Παρ Απρ 18, 2014 08:45 am

εμένα το lsmod μου δειχνει αυτο

Κώδικας: Επιλογή όλων

Module                  Size  Used by
ipt_IFWLOG             12622  2 
ipt_psd                57587  1 
ipt_rpfilter           12546  0 
xt_realm               12498  0 
cls_basic              12946  0 
cls_flow               17125  0 
cls_fw                 12904  0 
cls_u32                17137  0 
sch_fq_codel           17545  0 
sch_tbf                13137  0 
sch_prio               13152  0 
sch_hfsc               22164  0 
sch_htb                22278  0 
sch_ingress            12866  0 
sch_sfq                21416  0 
bridge                110673  0 
stp                    12976  1 bridge
llc                    14552  2 stp,bridge
ip6t_MASQUERADE        12768  0 
xt_CHECKSUM            12549  0 
ip6t_rpfilter          12546  0 
xt_statistic           12601  0 
xt_CT                  12956  36 
xt_LOG                 17717  10 
xt_connlimit           12636  0 
xt_addrtype            12635  4 
ip_set_hash_ip         27260  2 
xt_comment             12504  48 
xt_recent              18498  2 
ipt_ULOG               14273  0 
ipt_REJECT             12541  4 
ipt_MASQUERADE         12880  0 
ipt_ECN                12529  0 
ipt_CLUSTERIP          13508  0 
ipt_ah                 12806  0 
nf_nat_tftp            12489  0 
nf_nat_snmp_basic      17302  0 
nf_conntrack_snmp      12857  3 nf_nat_snmp_basic
nf_nat_sip             17152  0 
nf_nat_pptp            13115  0 
nf_nat_proto_gre       13009  1 nf_nat_pptp
xt_nat                 12681  0 
ip6table_nat           13015  0 
nf_nat_ipv6            13279  1 ip6table_nat
nf_nat_irc             12723  0 
xt_set                 13181  2 
ip_set                 36597  2 ip_set_hash_ip,xt_set
nf_nat_h323            17720  0 
nf_nat_ftp             12770  0 
nf_nat_amanda          12491  0 
nf_conntrack_tftp      13121  5 nf_nat_tftp
nf_conntrack_sane      13143  4 
nf_conntrack_sip       29764  5 nf_nat_sip
nf_conntrack_proto_udplite    13281  0 
nf_conntrack_proto_sctp    18822  0 
nf_conntrack_pptp      19258  3 nf_nat_pptp
nf_conntrack_proto_gre    14434  1 nf_conntrack_pptp
ts_kmp                 12605  5 
nf_conntrack_netlink    36189  0 
nf_conntrack_netbios_ns    12665  2 
nf_conntrack_broadcast    12589  2 nf_conntrack_netbios_ns,nf_conntrack_snmp
nf_conntrack_amanda    13041  5 nf_nat_amanda
nf_conntrack_irc       13518  3 nf_nat_irc
nf_conntrack_h323      73845  9 nf_nat_h323
nf_conntrack_ftp       18638  5 nf_nat_ftp
xt_TPROXY              17356  0 
xt_time                12661  0 
xt_TCPMSS              12707  0 
xt_tcpmss              12501  0 
xt_sctp                12853  0 
xt_policy              12582  0 
xt_pkttype             12504  0 
xt_physdev             12587  0 
xt_owner               12534  0 
xt_NFQUEUE             12776  0 
xt_NFLOG               12537  0 
nfnetlink_log          17879  1 xt_NFLOG
xt_multiport           12798  8 
xt_mark                12563  2 
xt_mac                 12492  0 
xt_limit               12711  0 
xt_length              12536  0 
xt_iprange             12783  0 
xt_helper              12583  0 
xt_hashlimit           17569  0 
xt_DSCP                12629  0 
xt_dscp                12597  0 
xt_dccp                12606  0 
xt_connmark            12755  0 
xt_CLASSIFY            12507  0 
ip6t_REJECT            12939  4 
xt_AUDIT               12678  0 
xt_tcpudp              12884  56 
nf_conntrack_ipv6      18894  23 
xt_state               12578  0 
nf_defrag_ipv6         34651  2 xt_TPROXY,nf_conntrack_ipv6
iptable_raw            12678  1 
iptable_nat            13011  0 
nf_nat_ipv4            13263  1 iptable_nat
nf_nat                 21568  15 nf_nat_ftp,nf_nat_irc,nf_nat_sip,nf_nat_amanda,ipt_MASQUERADE,nf_nat_proto_gre,ip6t_MASQUERADE,nf_nat_h323,nf_nat_ipv4,nf_nat_ipv6,nf_nat_pptp,nf_nat_tftp,xt_nat,ip6table_nat,iptable_nat
xt_conntrack           12760  17 
nf_conntrack_ipv4      15012  32 
nf_defrag_ipv4         12758  2 xt_TPROXY,nf_conntrack_ipv4
ip6table_raw           12683  1 
nf_conntrack           92796  39 nf_nat_ftp,nf_nat_irc,nf_nat_sip,nf_nat_amanda,xt_CT,nf_nat_snmp_basic,nf_conntrack_netbios_ns,nf_conntrack_proto_gre,xt_helper,ipt_MASQUERADE,nf_conntrack_proto_udplite,nf_nat,ip6t_MASQUERADE,xt_state,xt_connlimit,nf_nat_h323,nf_nat_ipv4,nf_nat_ipv6,nf_nat_pptp,nf_nat_tftp,xt_conntrack,nf_conntrack_amanda,ipt_CLUSTERIP,nf_conntrack_proto_sctp,nf_conntrack_netlink,ip6table_nat,nf_conntrack_broadcast,xt_connmark,nf_conntrack_ftp,nf_conntrack_irc,nf_conntrack_sip,iptable_nat,nf_conntrack_h323,nf_conntrack_ipv4,nf_conntrack_ipv6,nf_conntrack_pptp,nf_conntrack_sane,nf_conntrack_snmp,nf_conntrack_tftp
ip6table_mangle        12700  1 
iptable_mangle         12695  1 
nfnetlink              14606  3 nfnetlink_log,ip_set,nf_conntrack_netlink
iptable_filter         12810  1 
ip_tables              27239  4 iptable_filter,iptable_mangle,iptable_nat,iptable_raw
ip6table_filter        12815  1 
ip6_tables             27025  4 ip6table_filter,ip6table_mangle,ip6table_nat,ip6table_raw
x_tables               34059  59 xt_physdev,xt_pkttype,ip6table_filter,xt_statistic,xt_DSCP,xt_dccp,xt_dscp,xt_iprange,xt_mark,xt_sctp,xt_time,xt_CT,xt_helper,ip6table_mangle,ip6t_rpfilter,xt_length,xt_comment,ipt_ULOG,xt_policy,xt_CHECKSUM,xt_recent,ip_tables,xt_tcpmss,xt_tcpudp,ipt_MASQUERADE,ipt_ah,xt_AUDIT,xt_NFQUEUE,xt_NFLOG,ip6t_MASQUERADE,xt_limit,xt_owner,xt_realm,xt_state,ipt_rpfilter,xt_connlimit,xt_conntrack,xt_LOG,xt_mac,xt_nat,xt_set,ipt_IFWLOG,ipt_CLUSTERIP,xt_hashlimit,xt_multiport,iptable_filter,ip6table_raw,xt_CLASSIFY,xt_TCPMSS,xt_TPROXY,xt_connmark,ipt_REJECT,iptable_mangle,ipt_ECN,ipt_psd,ip6_tables,xt_addrtype,iptable_raw,ip6t_REJECT
af_packet              35649  4 
usb_storage            62062  0 
uvcvideo               80968  0 
videobuf2_vmalloc      13216  1 uvcvideo
videobuf2_memops       13362  1 videobuf2_vmalloc
videobuf2_core         40625  1 uvcvideo
snd_usb_audio         149112  1 
videodev              134653  2 uvcvideo,videobuf2_core
snd_usbmidi_lib        25070  1 snd_usb_audio
snd_rawmidi            30427  1 snd_usbmidi_lib
media                  21895  2 uvcvideo,videodev
snd_seq_device         14497  1 snd_rawmidi
arc4                   12608  2 
rt2800usb              27034  0 
rt2x00usb              20742  1 rt2800usb
hid_generic            12548  0 
usbhid                 48429  0 
hid                   105788  2 hid_generic,usbhid
rt2800pci              18719  0 
rt2800lib              88813  2 rt2800pci,rt2800usb
rt2x00pci              13287  1 rt2800pci
rt2x00mmio             13603  1 rt2800pci
rt2x00lib              55306  6 rt2x00pci,rt2x00usb,rt2800lib,rt2800pci,rt2800usb,rt2x00mmio
eeprom_93cx6           13344  1 rt2800pci
mac80211              516025  4 rt2x00lib,rt2x00pci,rt2x00usb,rt2800lib
snd_hda_codec_realtek    56661  1 
iTCO_wdt               13480  0 
gpio_ich               13476  0 
iTCO_vendor_support    13718  1 iTCO_wdt
snd_hda_intel          52267  5 
cfg80211              474802  2 mac80211,rt2x00lib
ppdev                  17635  0 
snd_hda_codec         192906  2 snd_hda_codec_realtek,snd_hda_intel
coretemp               13435  0 
snd_hwdep              17698  2 snd_usb_audio,snd_hda_codec
snd_pcm               102078  3 snd_usb_audio,snd_hda_codec,snd_hda_intel
microcode              19560  0 
lpc_ich                21080  0 
serio_raw              13413  0 
i2c_i801               22443  0 
crc_ccitt              12707  1 rt2800lib
rfkill                 22676  2 cfg80211
rng_core               13395  0 
r8169                  71677  0 
snd_page_alloc         18710  2 snd_pcm,snd_hda_intel
snd_timer              29378  1 snd_pcm
mii                    13934  1 r8169
snd                    83274  22 snd_hda_codec_realtek,snd_usb_audio,snd_hwdep,snd_timer,snd_pcm,snd_rawmidi,snd_usbmidi_lib,snd_hda_codec,snd_hda_intel,snd_seq_device
soundcore              15047  1 snd
shpchp                 37032  0 
parport_pc             41374  0 
parport                42264  2 ppdev,parport_pc
evdev                  17787  15 
cpufreq_ondemand       20254  2 
cpufreq_conservative    15314  0 
cpufreq_powersave      12618  0 
acpi_cpufreq           19790  0 
processor              31527  1 acpi_cpufreq
ipv6                  357086  54 ip6table_mangle,ip6t_rpfilter,bridge,nf_defrag_ipv6,ip6t_MASQUERADE,nf_nat_ipv6,ip6table_nat,xt_TPROXY,ip6t_REJECT,nf_conntrack_ipv6
autofs4                38674  2 
ehci_pci               12905  0 
ehci_hcd               71045  1 ehci_pci
uhci_hcd               32230  0 
usbcore               228902  10 uhci_hcd,snd_usb_audio,uvcvideo,rt2x00usb,usb_storage,rt2800usb,snd_usbmidi_lib,ehci_hcd,ehci_pci,usbhid
sr_mod                 22411  0 
usb_common             13057  1 usbcore
nouveau               952644  2 
button                 13871  1 nouveau
video                  19268  1 nouveau
mxm_wmi                13021  1 nouveau
wmi                    19177  2 mxm_wmi,nouveau
i2c_algo_bit           13413  1 nouveau
drm_kms_helper         44214  1 nouveau
ttm                    83917  1 nouveau
drm                   297706  4 ttm,drm_kms_helper,nouveau
i2c_core               40643  6 drm,i2c_i801,drm_kms_helper,i2c_algo_bit,nouveau,videodev
ide_pci_generic        12866  0 
ide_core              117183  1 ide_pci_generic
ata_generic            12910  0 
pata_acpi              13038  0 
ata_piix               35038  4 
έδωσα και

echo "blacklist asus_wmi" >> /etc/modprobe.d/blacklist-mga.conf

εκανα και μια επανεκκινηση αλλα δεν αλλαξε τιποτα
Intel Core i5-6300U CPU @ 2.40GHz ‖ RAM 7860 MiB ‖ HP 8079 - HP HP EliteBook 840 G3
Intel Skylake GT2 [HD Graphics 520] [8086:1916] {i915}
wlp2s0: Intel Wireless 8260 [8086:24f3] (rev 3a) ⋮ enp0s31f6: Intel Ethernet Connection I219-LM [8086:156f] (rev 21)

serma
Δημοσιεύσεις: 94
Εγγραφή: Σάβ Ιουν 02, 2012 19:22 pm

Re: προβλημα με wi-fi

Δημοσίευση από serma » Παρ Απρ 18, 2014 09:24 am

δώσε

Κώδικας: Επιλογή όλων

lspci -knn | grep -EiA3 net

Κώδικας: Επιλογή όλων

inxi -nz

Άβαταρ μέλους
airmaik
Δημοσιεύσεις: 637
Εγγραφή: Τρί Ιουν 07, 2011 16:44 pm

Re: προβλημα με wi-fi

Δημοσίευση από airmaik » Παρ Απρ 18, 2014 09:57 am

Κώδικας: Επιλογή όλων

lspci -knn | grep -EiA3 net

Κώδικας: Επιλογή όλων

03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 02)
	Subsystem: Gigabyte Technology Co., Ltd Device [1458:e000]
	Kernel driver in use: r8169
	Kernel modules: r8169
04:01.0 Network controller [0280]: Ralink corp. Device [1814:5362]
	Subsystem: Ralink corp. Device [1814:5362]
	Kernel modules: rt2800pci

Κώδικας: Επιλογή όλων

inxi -nz

Κώδικας: Επιλογή όλων

Network:   Card-1: Realtek RTL8101E/RTL8102E PCI Express Fast Ethernet controller driver: r8169 
           IF: enp3s0 state: down mac: <filter>
           Card-2: Ralink Device 5362 
           IF: N/A state: N/A speed: N/A duplex: N/A mac: N/A
           Card-3: Ralink RT5370 Wireless Adapter driver: rt2800usb 
           IF: wlp0s29f7u2 state: up mac: <filter>
τωρα ειμαι συνδεδεμενος με αυτο

http://www.tp-link.com/en/products/deta ... =TL-WN727N
Intel Core i5-6300U CPU @ 2.40GHz ‖ RAM 7860 MiB ‖ HP 8079 - HP HP EliteBook 840 G3
Intel Skylake GT2 [HD Graphics 520] [8086:1916] {i915}
wlp2s0: Intel Wireless 8260 [8086:24f3] (rev 3a) ⋮ enp0s31f6: Intel Ethernet Connection I219-LM [8086:156f] (rev 21)

Απάντηση

Μέλη σε σύνδεση

Μέλη σε αυτήν τη Δ. Συζήτηση: Δεν υπάρχουν εγγεγραμμένα μέλη και 1 επισκέπτης